EmbeddedRelated.com

ULINK for IAR (Crossworks)

Started by in LPC200015 years ago 25 replies

Hello! Can i use ULINK JTAG debugger with IAR or Crosswors studios? I search google and find no results :( -- Best regards, Roman...

Hello! Can i use ULINK JTAG debugger with IAR or Crosswors studios? I search google and find no results :( -- Best regards, Roman Antoshchenkov mailto:d...@rambler.ru ------------------------------------


lpc2148 prototype problem with JTAG (ULINK- Keil)

Started by zahovic in LPC200017 years ago 10 replies

Hello, I' ve just assembled a board with a LPC2148 and i can't connect with ULINK and Keil. I can download software using internal...

Hello, I' ve just assembled a board with a LPC2148 and i can't connect with ULINK and Keil. I can download software using internal bootloader and com0 (p0.14 pulldown) with LPC210x_ISP utility. i have a prototype board from Olimex, and i can download software in both modes (ISP and JTAG), so my ulink is working. But on my own prototype when i try to download, keil shows a message: "...


ULink clone

Started by Sagaert Johan in LPC200017 years ago 5 replies

Hi I wonder if someone attemted to clone the ulink ? It seems to only contain some standard components ( 2x LVC244, 32K sram ,eeprom and...

Hi I wonder if someone attemted to clone the ulink ? It seems to only contain some standard components ( 2x LVC244, 32K sram ,eeprom and Cypress AN2131 ) The eeprom can be read using the cypress tools (already done here). I am playing with the idea to make some, maybe i will (is the some interrest in this ?) J.


ulink schematics

Started by Amr Taha in LPC200017 years ago 2 replies

Dear All, I'm a new commer to the ARM world from the 8-bit world. I'm now in the learning phase and collecting the required tools. I have...

Dear All, I'm a new commer to the ARM world from the 8-bit world. I'm now in the learning phase and collecting the required tools. I have downloaded the ulink schematics from the group's file section but unluckily, didn't find the USB-Controller AN2131 at any distributer. Cypress is not recommending it for new designs. Please give me an advice. Many thanks. ---------------------------...


which jtag is better?

Started by naderus2000 in LPC200018 years ago 20 replies

i want to between j-link and ULink which one is better? is both of them work in IAR and keil?

i want to between j-link and ULink which one is better? is both of them work in IAR and keil?


Wiggler and Keil

Started by vineet jain in LPC200019 years ago 17 replies

Hello everyone, Can i hardware debug my code using Wiggler with Keil, or it only works with Ulink. Regards, Vineet. ...

Hello everyone, Can i hardware debug my code using Wiggler with Keil, or it only works with Ulink. Regards, Vineet. __________________________________________________ "> http://mail.yahoo.com


LPC2129/LPC2194

Started by ualbe in LPC200019 years ago 9 replies

Dear LPC2000 group, I'm new to ARM chip and i'm starting to develope with LPC2129/LPC2194. Some simple but fundamental questions: 1-...

Dear LPC2000 group, I'm new to ARM chip and i'm starting to develope with LPC2129/LPC2194. Some simple but fundamental questions: 1- which is the best toolchain to work with? 2- there are someone working with GCC/Keil/ULINK set? 3- there are someone working with winIdea? thanks in advance alberto ubertelli


ISP programming with lpc21isp utility

Started by tclarke1 in LPC200016 years ago 3 replies

What are all the tricks to get the lpc21isp (v1.48) utility to actually work? I have the EA LPC2478 board. I have a ulink and flashmagic, but...

What are all the tricks to get the lpc21isp (v1.48) utility to actually work? I have the EA LPC2478 board. I have a ulink and flashmagic, but I'd like to know all the options for burning code. I finally figured out that the lpc util does not control the state of RST and P2.10 like flashmagic does, so I have learned to press the two related buttons on the board as needed. When I try: >


JTAG Pull-up/Pull-down

Started by georgeioak in LPC200018 years ago 3 replies

Hello Everyone: We just started working on our first design based on the LPC2101 part. We have a Keil MDB2103 Eval Board and followed the...

Hello Everyone: We just started working on our first design based on the LPC2101 part. We have a Keil MDB2103 Eval Board and followed the reference design schematic for the JTAG interface which showed TCK and RTCK being pulled down. We had nothing but troubles trying to get the ULINK JTAG adapter communicating and only after we changed these 2 signals to being pull-ups did we successf...


LPC2194 JTAG programming problems...

Started by gregdeuerling in LPC200020 years ago 1 reply

I've two Philips LPC designs. One uses a LPC2294 and the other a LPC2194. I've been working on the LPC2294 design for some time...

I've two Philips LPC designs. One uses a LPC2294 and the other a LPC2194. I've been working on the LPC2294 design for some time and have not had any problems at all. My LPC2194 design is a different story. I'm using the Keil DKARM (V1.4) and ULINK to program the LPC's via


Re: Debugger for Keil

Started by Sagaert Johan in LPC200013 years ago 4 replies

try ebay i payed 55$ for an ulink2 on ebay ----- Original Message ----- From: Jorge Polar To: l...@yahoogroups.com Sent: Sunday,...

try ebay i payed 55$ for an ulink2 on ebay ----- Original Message ----- From: Jorge Polar To: l...@yahoogroups.com Sent: Sunday, July 10, 2011 6:45 PM Subject: [lpc2000] Debugger for Keil Hello friends, Does anybody knows if there is another HW debugger/emulator for the Keil and LPC2000/LPC1000 devices, besides the ULINK2 or ULINK-PRO? Something cheap...


LPC2131 SPI output drive and ULINK JTAG issues

Started by drb5599 in LPC200019 years ago 2 replies

Hello All, After several months of developing with the MCB2130 eval board I finally got my first prototype hardware. I am pretty excited,...

Hello All, After several months of developing with the MCB2130 eval board I finally got my first prototype hardware. I am pretty excited, but I have a couple issues. My first big issue is the SPI output signals. I am communicating with two other devices over an SPI bus where the LPC is the master. The signals coming out of the LPC are correct, e


LPC2138 will not come out of bootloader mode

Started by kennytrussell in LPC200018 years ago 3 replies

I have a board containing an LPC2138. I cannot get the chip to come out of bootloader mode or at least that is what I think is happening. I...

I have a board containing an LPC2138. I cannot get the chip to come out of bootloader mode or at least that is what I think is happening. I can load programs with no errors through a Keil ULINK but when I go into debug, the code I see starting at address 0 is not my code but instead is a mirror of the bootloader. I can also use the LPC2000 Flash Utility to load the chip, examine the buf...


LPC2148 bulk/production programming

Started by Sutton Mehaffey in LPC200012 years ago 7 replies

I have Keil uVision software for development and a ULINK 2 for programming via a 20 pin JTAG on the circuit board (LPC2148). What is the...

I have Keil uVision software for development and a ULINK 2 for programming via a 20 pin JTAG on the circuit board (LPC2148). What is the easiest approach for initial production programming of these devices on circuit boards (we have SD card updates - but the board must be programmed with a bootloader and production code for the first time)? Meaning, I don't want to include the source f...


does IAR can work with N-Link ARM USB JTAG?

Started by naderus2000 in LPC200018 years ago 1 reply

Hi, does IAR can work with N-Link ARM USB JTAG? i read it Compatible with ULINK 100% so no problem in keil but i want to know about iar. it's...

Hi, does IAR can work with N-Link ARM USB JTAG? i read it Compatible with ULINK 100% so no problem in keil but i want to know about iar. it's only $50. here is the link: http://www.micro4you.com/product_info.php? products_id=87&osCsid=96225f362c57ecd96ad921a06829a115


uVision3 error message: "Missing Device (R003....)"

Started by ottorichter100 in LPC200018 years ago 2 replies

Hi out there, I'm new to ARM-Controllers and KEIL uVision. I'm using the trial version (restricted version), with Keil tool-chain on a...

Hi out there, I'm new to ARM-Controllers and KEIL uVision. I'm using the trial version (restricted version), with Keil tool-chain on a WIN2000-PC Compiling works, also loading into LPC2103 (with ULINK). The compiler tells me that I use 12% of code limit of the trial version. BUT: When I want to start my program on the LPC2103 by the debugger I get the following message: MISSING DEVIC...


MCB2100 LPC2114 starter code

Started by petermccormick1 in LPC200021 years ago 2 replies

We have used Keil Uv2 (assemblers & C) and Ceibo emulators & programmers for the 87C554 family of chips for years. The 87C is great but it is...

We have used Keil Uv2 (assemblers & C) and Ceibo emulators & programmers for the 87C554 family of chips for years. The 87C is great but it is becoming an antique. We are migrating to the LPC2114 and have purchased the Keil Ulink and MCB2100 to ramp up. Keil does not seem to have much sample code to work with the MCB2100 for starters. Are there any web sites with code, flash programmin


LPC2468 & Jtag Failure

Started by maveric_pta in LPC200014 years ago 4 replies

I have design my own custom Board. I have confirmed that all JTAG connections are correct and have confirmed my ULink-ME is working on a STM32...

I have design my own custom Board. I have confirmed that all JTAG connections are correct and have confirmed my ULink-ME is working on a STM32 development board. I am using uVision4. Using standard Blinky project from Keil. When I tried to connect to the CPU I get JTAG Communication Failure. I have confirmed that all pull up and pull down resistors are correct on JTAG .. I have assembled a ...


I can download the program to MCU (LPC2468) on Keil ULink

Started by wilnfl in LPC200017 years ago 4 replies

I use LPC2468. I has write some code to control PWM, and I set the PCON = 0x2, so the system enter power down mode, and then, I cann't...

I use LPC2468. I has write some code to control PWM, and I set the PCON = 0x2, so the system enter power down mode, and then, I cann't download any program to this chip, because every time this board power up, it enter power down mode, so I cann't connect jtag. Anybody has any method to solve this problem? Thanks in advacne.


External Flash Algorithms intel TE28F160C3BD70

Started by civcivonur in LPC200017 years ago 1 reply

Hi, I have a LPC2294 Development Board. http://www.olimex.com/dev/images/LPC-L2294-1MB-sch.gif i could not use the external flash. I search...

Hi, I have a LPC2294 Development Board. http://www.olimex.com/dev/images/LPC-L2294-1MB-sch.gif i could not use the external flash. I search for the code of intel TE28F160C3BD70 programming but i could not find. So i try to modify the code of RC28F320J that is writen by Keil. But when i try to load the program with this code Ulink says "Can not load Flash Programming Algorithm" & "Insuffi...