Working with Microchip PIC 8-bit GPIO
The third in a series of five posts looks at GPIO with PIC 8-bit microcontrollers. After a detailed review of the registers for configuring and managing GPIO on the PIC18F47Q10 processor, a basic application is stood up programming those registers to blink external LEDs at 0.5Hz.
Blinkenlights 2.0
Nothing spells old movie computers like a panel of randomly blinking lights, but in fact, these so-called "blinkenlights" can be valuable indicators - especially in embedded systems where the user interface must be minimal, small and cheap. Control of these lights can be achieved using a very simple, real-time interpreted script, and this kind of solution may be extended to other and more complex embedded tasks.
Understanding Microchip 8-bit PIC Configuration
The second post of a five part series picks up getting started developing with Microchip 8-bit PIC Microcontroller by examining the how and why of processor configuration. Topics discussed include selecting the oscillator to use during processor startup and refining the configuration once the application starts. A walk through of the code generated by the Microchip IDE provides a concrete example of the specific Configuration Word and SFR values needed to configure the project specific clock configuration.
Getting Started with the Microchip PIC® Microcontroller
This first post of a five part series looks at the available hardware options for getting started with Microchip 8-bit PIC® Microcontroller, explores the MPLAB® X Integrated Development Environment and walks through setting up a project to expose the configured clock to an external pin and implement a single output GPIO to light an LED.
Make Your Own MCU Boards (2023 Teardown Conference)
Ditch the development boards! Products like the Nucleo development boards serve a wonderful purpose, but they’re ill-suited for projects that need to be small and cheap, such as hobby projects or products just beginning a production run. In this talk (a recording from the 2023 Teardown Conference), you’ll learn how to put a microcontroller or other custom circuit on a PCB a little larger than a stick of gum for less than $3 a board.
Getting Started With Zephyr: Writing Data to EEPROM
In this blog post, I show how to implement a Zephyr application to interact with EEPROM. I show how the Zephyr device driver model allows application writers to be free of the underlying implementation details. Unfortunately, the application didn't work as expected, and I'm still troubleshooting the cause.
Getting Started With Zephyr: Saving Data To Files
In this blog post, I show how to implement a Zephyr application to mount a microSD card, create a new file on the microSD card, and write data to it. The lessons learned from such an application can be helpful for devices out in the field that need to write data to off-board memory periodically, especially in cases where Internet access may be sporadic.
Creating a Hardware Abstraction Layer (HAL) in C
In my last post, C to C++: Using Abstract Interfaces to Create Hardware Abstraction Layers (HAL), I discussed how vital hardware abstraction layers are and how to use a C++ abstract interface to create them. You may be thinking, that’s great for C++, but I work in C! How do I create a HAL that can easily swap in and out different drivers? In today’s post, I will walk through exactly how to do that while using the I2C bus as an example.
What does it mean to be 'Turing complete'?
The term "Turing complete" describes all computers and even some things we don't expect to be as powerful as a typical computer. In this article, I describe what it means and discuss the implications of Turing completeness on projects that need just a little more power, on alternative processor designs, and even security.
Getting Started With Zephyr: Devicetree Overlays
In this blog post, I show how the Devicetree overlay is a valuable construct in The Zephyr Project RTOS. Overlays allow embedded software engineers to override the default pin configuration specified in Zephyr for a particular board. In this blog post, I use I2C as an example. Specifically, I showed the default I2C pins used for the nRF52840 development kit in the nominal Zephyr Devicetree. Then, I demonstrated how an overlay can be used to override this pin configuration and the final result.
Introduction to Microcontrollers - Timers
Time is everything in embedded systems, and Mike Silva walks through how microcontroller timers turn clock pulses into dependable events. He covers prescalers, counter bit widths, overflow versus compare modes, atomic multi-byte register access, the "-1 rule", input capture and compare leapfrogging, with concrete AVR and STM32 code that highlights common pitfalls and reliable patterns for precise ticks.
Getting Started with (Apache) NuttX RTOS - Part 1
NuttX RTOS is used in many products from companies like Sony, Xiaomi, Samsung, Google/Fitbit, WildernessLabs and many other companis. So, probably you are already using NuttX even without knowing it, like the you was using Linux on your TV, WiFi router more than 10 years ago and didn't know too! Today you will have the chance to discover a little bit of this fantastic Linux-like RTOS! Are you ready? So, let's get started!
Getting Started With Zephyr: Saving Data To Files
In this blog post, I show how to implement a Zephyr application to mount a microSD card, create a new file on the microSD card, and write data to it. The lessons learned from such an application can be helpful for devices out in the field that need to write data to off-board memory periodically, especially in cases where Internet access may be sporadic.
Introduction to Microcontrollers - Driving WS2812 RGB LEDs
Mike Silva walks through a practical, cycle-counted AVR assembly implementation to bit-bang WS2812B RGB LEDs from an 8MHz AVR, hitting the chip's tight 1.25µs-per-bit timing. The post breaks down the WS2812B self-clocked protocol and GRB byte order, explains register and calling-convention choices, and includes a complete C example plus power-consumption warnings for driving LED strips.
Introduction to Microcontrollers - 7-segment displays & Multiplexing
Seven-segment displays can eat dozens of GPIO pins and dozens of resistors, but multiplexing trades pins for time and cuts component count dramatically. Mike Silva shows a hands-on AVR C implementation with segment encoding, a 100 Hz display scan ISR, several integer-to-digit conversion techniques, and software workarounds for messy pin mappings. He also demonstrates a timer "leapfrog" to reuse one timer for two tasks and compares performance so you can choose the best approach for your MCU.
How to Design Reliable Reset Circuits for Embedded Microcontrollers
In the world of embedded systems, the reset circuit is a critical component that ensures the microcontroller starts up correctly and recovers gracefully from unexpected events like power fluctuations or software crashes. A poorly designed reset circuit can lead to erratic behavior, system lockups, or even permanent damage to the microcontroller. For embedded engineers, designing a reliable reset circuit is essential for ensuring the stability and robustness of the system.
From Baremetal to RTOS: A review of scheduling techniques
Jacob Beningo walks through five common embedded scheduling techniques, showing how each scales from a single super loop to a full RTOS. He highlights practical trade-offs for round-robin, interrupt-driven, queued, cooperative, and RTOS approaches so you can spot when timing becomes fragile and when added complexity is justified. This primer sets up the next post on when to adopt an RTOS.
Learning A New Microcontroller
Learning a new microcontroller becomes manageable with a repeatable, stepwise process that focuses on common peripherals, tools, and example programs. This post lays out hands-on exercises from blinky and UART echoes through I2C/SPI, PWM and ADC to DMA and RTOS variations, and shows how to evolve prototype code into reusable HAL and OSAL layers. Practical tips cover hardware setup, logic analyzers, and keeping an engineering notebook.
Introduction to Microcontrollers - More On GPIO
Polarity matters: an output '1' does not always mean an LED lights, and inputs are just as picky. This post walks through LED driving basics, pull resistors for buttons, and practical bitwise techniques to read and write individual GPIO pins on AVR and STM32 boards. It also explains why polling rates and mechanical bounce make button handling trickier than it looks and what to watch for next.
Cortex-M Exception Handling (Part 2)
Exception entry and return on Cortex-M look simple, but the hardware does a lot to preserve context, enforce privilege, and pick the right stack. This post walks through the processor actions after an exception is accepted: which registers get pushed, how CONTROL, MSP and PSP affect stack selection, how EXC_RETURN encodes the return path, and why VTOR and vector table alignment matter for handler lookup.
Introduction to Microcontrollers - More On GPIO
Polarity matters: an output '1' does not always mean an LED lights, and inputs are just as picky. This post walks through LED driving basics, pull resistors for buttons, and practical bitwise techniques to read and write individual GPIO pins on AVR and STM32 boards. It also explains why polling rates and mechanical bounce make button handling trickier than it looks and what to watch for next.
From Baremetal to RTOS: A review of scheduling techniques
Jacob Beningo walks through five common embedded scheduling techniques, showing how each scales from a single super loop to a full RTOS. He highlights practical trade-offs for round-robin, interrupt-driven, queued, cooperative, and RTOS approaches so you can spot when timing becomes fragile and when added complexity is justified. This primer sets up the next post on when to adopt an RTOS.
Introduction to Microcontrollers - Button Matrix & Auto Repeating
Wiring every button to its own GPIO gets expensive fast, so Mike Silva shows how to read a 4x4 keypad with only eight pins using matrix scanning. He then builds the raw scan into a debounced state machine, adds auto-repeat, and even extends it to a two-stage repeat rate. The result is a practical, code-heavy walkthrough for turning a keypad into clean button events on AVR and STM32.
Introduction to Microcontrollers - 7-segment displays & Multiplexing
Seven-segment displays can eat dozens of GPIO pins and dozens of resistors, but multiplexing trades pins for time and cuts component count dramatically. Mike Silva shows a hands-on AVR C implementation with segment encoding, a 100 Hz display scan ISR, several integer-to-digit conversion techniques, and software workarounds for messy pin mappings. He also demonstrates a timer "leapfrog" to reuse one timer for two tasks and compares performance so you can choose the best approach for your MCU.
Cortex-M Exception Handling (Part 1)
This article describes how Cortex-M processors handle interrupts and, more generally, exceptions, a concept that plays a central role in the design and implementation of most embedded systems.
Introduction to Microcontrollers - More On Interrupts
Interrupts are powerful but dangerous, and Mike Silva breaks down how they actually behave on microcontrollers and why they can corrupt data. This post explains latched flags, pending and priority behavior, ISR nesting, and common read-modify-write hazards, then shows practical fixes like targeted interrupt masking and using atomic GPIO hardware so you can stop chasing sporadic bugs.
Slew Rate Limiters: Nonlinear and Proud of It!
Slew-rate limits are a small nonlinear detail that often decides whether a controller behaves nicely or wrecks hardware. Jason Sachs walks through why slew limits appear in electronics and actuators, then shows two practical digital ways to impose limits: constraining input increments and constraining input around the output. He compares performance on underdamped second-order systems, gives closed-form intuition for overshoot, and demonstrates simulations with scipy and ODE solvers.
Arduino robotics #4 - HC-SR04 ultrasonic sensor
Lonnie Honeycutt shows how to turn a $50 mobile platform into a simple autonomous robot by adding an HC-SR04 ultrasonic sensor to an Arduino. The post walks through wiring, a minimal test sketch and the integration code used on Clusterbot, plus practical tips on range limits, motor choices and library options to make obstacle avoidance reliable for hobby builds.
From bare-metal to RTOS: 5 Reasons to use an RTOS
Most developers default to bare-metal, but Jacob Beningo argues an RTOS often simplifies modern embedded design. He outlines five practical reasons to move to an RTOS: easier integration of connectivity stacks and GUIs, true preemptive scheduling with priorities, tunable footprints, API-driven portability, and a common toolset for tasks and synchronization. The piece helps decide when RTOS adoption speeds development.
Cortex-M Exception Handling (Part 2)
Exception entry and return on Cortex-M look simple, but the hardware does a lot to preserve context, enforce privilege, and pick the right stack. This post walks through the processor actions after an exception is accepted: which registers get pushed, how CONTROL, MSP and PSP affect stack selection, how EXC_RETURN encodes the return path, and why VTOR and vector table alignment matter for handler lookup.
