EmbeddedRelated.com

Simulating Your Embedded Project on Your Computer (Part 1)

Nathan Jones October 2, 2024

Having a simulation of your embedded project is like having a superpower that improves the quality and pace of your development ten times over! To be useful, though, it can't take longer to develop the simulation than it takes to develop the application code and for many simulation techniques "the juice isn't worth the squeeze"! In this two-part blog series, I'll share with you the arguments in favor of simulation (so, hopefully, you too believe in its value) and I'll show you what works (and what doesn't work) to help you to simply, easily, and quickly simulate your embedded project on your computer.


My friend, the compiler

Ido Gendel September 11, 2024

Modern compilers were given great powers, but we don't always know where and when they'll use them. This may cause us to either worry needlessly or trust unjustifiably, as demonstrated by a little example in this post.


Write Better Code with Block Diagrams and Flowcharts

Nathan Jones August 1, 20241 comment

Reading and writing code without architectural diagrams is like trying to follow complex instructions without any explanatory pictures: nigh impossible! By taking the time to draw out the block diagrams and flowcharts for your code, you can help identify problems before they arise and make your code easier to design, write, test, and debug. In this article, I'll briefly justify the importance of architectural drawings such as block diagrams and flowcharts and then teach you what they are and how to draw them. Using two simple examples, you'll see first-hand how these drawings can significantly amplify your understanding of a piece of code. Additionally, I'll give you a few tips for how to implement each drawing once you've completed it and I'll share with you a few neat tools to help you complete your next set of drawings.


7 Essential Steps for Reducing Power Consumption in Embedded Devices

Jacob Beningo June 26, 20241 comment

Reducing the amount of power your embedded device is consuming is not trivial. With so many devices moving to battery operations today, maximizing battery life can be the difference between a happy, raving customer and an unhappy one that ruins your company's reputation. This post explores seven steps for optimizing your embedded systems' power consumption. You'll gain insights into the steps and techniques necessary along with receiving a few resources to help you on your journey.


Introduction to PIC Timers

Luther Stanton May 8, 2024

The fourth in a series of five posts looks at 8-bit PIC hardware timers. After a review of basic timer functionality, the Timer0 module operation and configuration is reviewed and a basic application implemented using Timer0 to blink external LEDs at a frequency of 0.5Hz.


Working with Microchip PIC 8-bit GPIO

Luther Stanton April 24, 20241 comment

The third in a series of five posts looks at GPIO with PIC 8-bit microcontrollers. After a detailed review of the registers for configuring and managing GPIO on the PIC18F47Q10 processor, a basic application is stood up programming those registers to blink external LEDs at 0.5Hz.


Blinkenlights 2.0

Ido Gendel April 17, 2024

Nothing spells old movie computers like a panel of randomly blinking lights, but in fact, these so-called "blinkenlights" can be valuable indicators - especially in embedded systems where the user interface must be minimal, small and cheap. Control of these lights can be achieved using a very simple, real-time interpreted script, and this kind of solution may be extended to other and more complex embedded tasks.


Understanding Microchip 8-bit PIC Configuration

Luther Stanton March 26, 20243 comments

The second post of a five part series picks up getting started developing with Microchip 8-bit PIC Microcontroller by examining the how and why of processor configuration. Topics discussed include selecting the oscillator to use during processor startup and refining the configuration once the application starts. A walk through of the code generated by the Microchip IDE provides a concrete example of the specific Configuration Word and SFR values needed to configure the project specific clock configuration.


Getting Started with the Microchip PIC® Microcontroller

Luther Stanton March 11, 2024

This first post of a five part series looks at the available hardware options for getting started with Microchip 8-bit PIC® Microcontroller, explores the MPLAB® X Integrated Development Environment and walks through setting up a project to expose the configured clock to an external pin and implement a single output GPIO to light an LED.


Make Your Own MCU Boards (2023 Teardown Conference)

Nathan Jones March 7, 2024

Ditch the development boards! Products like the Nucleo development boards serve a wonderful purpose, but they’re ill-suited for projects that need to be small and cheap, such as hobby projects or products just beginning a production run. In this talk (a recording from the 2023 Teardown Conference), you’ll learn how to put a microcontroller or other custom circuit on a PCB a little larger than a stick of gum for less than $3 a board.


Introduction to Microcontrollers - Beginnings

Mike Silva August 20, 201313 comments

Welcome to this Introduction to Microcontroller Programming tutorial series. If you are looking to learn the basics of embedded programming for microcontrollers (and a bit of embedded hardware design as well), I hope these tutorials will help you along that journey. These are my first postings here, and I am writing this tutorial series because over the years I have seen countless newbies asking the same questions and tripping over the same stumbling blocks, and I thought I might be able to...


Analyzing the Linker Map file with a little help from the ELF and the DWARF

Govind Mukundan December 27, 201522 comments

When you're writing firmware, there always comes a time when you need to check the resources consumed by your efforts - perhaps because you're running out of RAM or Flash or you want to optimize something. The map file generated by your linker is a useful tool to aid in the resource analysis. I wanted to filter and sort the data generated in an interactive way so I wrote a C# WinForms application that reads the data from the map and presents it in a list view (using the awesome


Introduction to Microcontrollers - Driving WS2812 RGB LEDs

Mike Silva November 14, 201330 comments

This tutorial chapter is a bit of a detour, but I think an interesting and useful one.  It introduces a bit of assembly language programming, and demonstrates bit-banging a tight serial data protocol.  And it deals with RGB LEDs, which are just very fun in their own right, especially these new parts.  So I thought I'd post this to give readers time for some holiday lighting experimenting.

Back To The Future

Remember how we started this...


Introduction to Microcontrollers - Interrupts

Mike Silva September 18, 20136 comments

It's Too Soon To Talk About Interrupts!

That, at least, could be one reaction to this chapter.  But over the years I've become convinced that new microcontroller programmers should understand interrupts before being introduced to any complex peripherals such as timers, UARTs, ADCs, and all the other powerful function blocks found on a modern microcontroller.  Since these peripherals are commonly used with interrupts, any introduction to them that does not...


Introduction to Microcontrollers - Hello World

Mike Silva September 11, 201316 comments

Embedded Hello World

A standard first program on an embedded platform is the blinking LED.  Getting an LED to blink demonstrates that you have your toolchain set up correctly, that you are able to download your program code into the μC, and that the μC and associated circuitry (e.g. the power supply) is all working.  It can even give you good evidence as to the clock rate that your microcontroller is running (something that trips up a great many people,...


Introduction to Microcontrollers - Timers

Mike Silva September 27, 20132 comments

Timers - Because "When" Matters

Computer programs are odd things, for one reason because they have no concept of time.  They may have the concept of sequential execution, but the time between instructions can be essentially any number and the program won't notice or care (unless assumptions about time have been built into the program by the programmer).  But the real world is not like this.  In the real world, especially the real embedded world,...


Introduction to Microcontrollers - Further Beginnings

Mike Silva September 1, 20134 comments
Embedded Programming Basics

This tutorial entry will discuss some further embedded programming basics that you will need to understand before proceeding on to the LED blinky and other example programs. We will do this by looking at the general organization and types of instructions found in most microcontrollers, and how that organization and those instructions are reflected (or, in some cases, ignored) by the C programming language.

Basic CPU...

Arduino robotics #1 - motor control

Lonnie Honeycutt October 13, 20133 comments
Arduino Robotics

Beginner robotics is a series of article chronicling my first autonomous robot build, Clusterbot.  This build is meant to be affordable, relatively easy and instructive.  The total cost of the build is around $50.  

1. Arduino robotics - motor control2. Arduino robotics - chassis, locomotion and power3. Arduino robotics - wiring, coding and a test run4. 

Introduction to Microcontrollers - Buttons and Bouncing

Mike Silva October 26, 20133 comments

What Is A Button?

To your hardware, that is.  As discussed in Introduction to Microcontrollers - More On GPIO, a button (or key, or switch, or any form of mechanical contact) is generally hooked up to a microcontroller so as to generate a certain logic level when pushed or closed or "active," and the opposite logic level when unpushed or open or "inactive."  The active logic level can be either '0' or '1', but for reasons both historical and electrical, an...


Introduction to Microcontrollers - More On GPIO

Mike Silva September 13, 20134 comments

Now that we have our LED Blinky program nailed down, it's time to look more closely at outputs, add button/switch inputs, and work with reading inputs and driving outputs based on those inputs.

It's ON - No, It's OFF - No, It's ON...

I have to confess, I cheated.  Well, let's say I glossed over something very important.  In our LED Blinky program, we never cared about whether an output '1' or an output '0' turned on the LED.  Since we were just...