First Steps in OrCAD 16 [Capture]
Hello community, I know that in last posts I have been writting about the Software. But what about Hardware? In last months I have been dealing with it, exactly with OrCAD 16. And I will explain how to build a PCB in 2 articles. For begginers could be a good and easy guide.
This article explains the part for the designing of the schematic, and in the next one which i will explain the layout part.
The first stuff you must known about OrCAD is that it is not an unique tool for...
Have You Ever Seen an Ideal Op-Amp?
Somewhere, along with unicorns and the Loch Ness Monster, lies a small colony of ideal op-amps. Op-amp is short for operational amplifier, and we start our education on them by learning about these mythical beasts, which have the following properties:
- Infinite gain
- Infinite input impedance
- Zero output impedance
And on top of it all, they will do whatever it takes to change their output in order to make their two inputs equal.
But they don't exist. Real op-amps have...
Hot Fun in the Silicon: Thermal Testing with Power Semiconductors
Here's a trick that is useful the next time you do thermal testing with your MOSFETs or IGBTs.
Thermal testing?!
Yes, that's right. It's important to make sure your power transistors don't overheat. In the datasheet, you will find some information that you can use to estimate how hot the junction inside the IC will get.
Let's look at an example. Here's a page from the IRF7739 DirectFET datasheet. I like this datasheet because it has almost all the thermal stuff on one page,...
10 More (Obscure) Circuit Components You Should Know
The interest in my previous article on obscure but useful electronics parts, "10 Circuit Components You Should Know" was encouraging enough that I thought I would write a followup. So here are another 10:
1. "Ideal Diode" controllers
Load-sharing circuits use diodes tied together at their cathode terminal to take the most positive voltage among the sources and connect it to a load. Works great: you have a DC/DC power supply, a battery, and a solar cell, and it will use whichever output is...
Stairway to Thévenin
This article was inspired by a recent post on reddit asking for help on Thévenin and Norton equivalent circuits.
(With apologies to Mr. Thévenin, the rest of the e's that follow will remain unaccented.)
I still remember my introductory circuits class on the subject, roughly as follows:
(NOTE: Do not get scared of what you see in the rest of this section. We're going to point out the traditional approach for teaching linear equivalent circuits first. If you have...
10 Circuit Components You Should Know
Chefs have their miscellaneous ingredients, like condensed milk, cream of tartar, and xanthan gum. As engineers, we too have quite our pick of circuits, and a good circuit designer should know what's out there. Not just the bread and butter ingredients like resistors, capacitors, op-amps, and comparators, but the miscellaneous "gadget" components as well.
Here are ten circuit components you may not have heard of, but which are occasionally quite useful.
1. Multifunction gate (
Analog-to-Digital Confusion: Pitfalls of Driving an ADC
Imagine the following scenario:You're a successful engineer (sounds nice, doesn't it!) working on a project with three or four circuit boards. More than even you can handle, so you give one of them over to your coworker Wayne to design. Wayne graduated two years ago from college. He's smart, he's a quick learner, and he's really fast at designing schematics and laying out circuit boards. It's just that sometimes he takes some shortcuts... but in this case the circuit board is just something...
Which MOSFET topology?
A recent electronics.StackExchange question brings up a good topic for discussion. Let's say you have a power supply and a 2-wire load you want to be able to switch on and off from the power supply using a MOSFET. How do you choose which circuit topology to choose? You basically have four options, shown below:
From left to right, these are:
High-side switch, N-channel MOSFET High-side switch, P-channel MOSFET Low-side switch, N-channel...Thermistor signal conditioning: Dos and Don'ts, Tips and Tricks
In an earlier blog entry, I mentioned this circuit for thermistor signal conditioning:
It is worth a little more explanation on thermistor signal conditioning; it's something that's often done poorly, whereas it's among the easiest applications for signal conditioning.
The basic premise here is that there are two resistors in a voltage divider: Rth is the thermistor, and Rref is a reference resistor. Here Rref is either R3 alone, or R3 || R4, depending on the gain...
Real-time clocks: Does anybody really know what time it is?
We recently started writing software to make use of a real-time clock IC, and found to our chagrin that the chip was missing a rather useful function, namely elapsed time in seconds since the standard epoch (January 1, 1970, midnight UTC).Let me back up a second.A real-time clock/calendar (RTC) is a micropower chip that has an oscillator on it that keeps counting time, independent of main system power. Usually this is done with a lithium battery that can power the RTC for years, so that even...
Wye Delta Tee Pi: Observations on Three-Terminal Networks
Today I’m going to talk a little bit about three-terminal linear passive networks. These generally come in two flavors, wye and delta.
Why Wye?The town of Why, Arizona has a strange name that comes from the shape of the original road junction of Arizona State Highways 85 and 86, which was shaped like the letter Y. This is no longer the case, because the state highway department reconfigured the intersection
Real-time clocks: Does anybody really know what time it is?
We recently started writing software to make use of a real-time clock IC, and found to our chagrin that the chip was missing a rather useful function, namely elapsed time in seconds since the standard epoch (January 1, 1970, midnight UTC).Let me back up a second.A real-time clock/calendar (RTC) is a micropower chip that has an oscillator on it that keeps counting time, independent of main system power. Usually this is done with a lithium battery that can power the RTC for years, so that even...
Voltage Drops Are Falling on My Head: Operating Points, Linearization, Temperature Coefficients, and Thermal Runaway
Today’s topic was originally going to be called “Small Changes Caused by Various Things”, because I couldn’t think of a better title. Then I changed the title. This one’s not much better, though. Sorry.
What I had in mind was the Shockley diode equation and some other vaguely related subjects.
My Teachers Lied to MeMy introductory circuits class in college included a section about diodes and transistors.
The ideal diode equation is...
First Steps in OrCAD 16 [Capture]
Hello community, I know that in last posts I have been writting about the Software. But what about Hardware? In last months I have been dealing with it, exactly with OrCAD 16. And I will explain how to build a PCB in 2 articles. For begginers could be a good and easy guide.
This article explains the part for the designing of the schematic, and in the next one which i will explain the layout part.
The first stuff you must known about OrCAD is that it is not an unique tool for...
10 More (Obscure) Circuit Components You Should Know
The interest in my previous article on obscure but useful electronics parts, "10 Circuit Components You Should Know" was encouraging enough that I thought I would write a followup. So here are another 10:
1. "Ideal Diode" controllers
Load-sharing circuits use diodes tied together at their cathode terminal to take the most positive voltage among the sources and connect it to a load. Works great: you have a DC/DC power supply, a battery, and a solar cell, and it will use whichever output is...
Hot Fun in the Silicon: Thermal Testing with Power Semiconductors
Here's a trick that is useful the next time you do thermal testing with your MOSFETs or IGBTs.
Thermal testing?!
Yes, that's right. It's important to make sure your power transistors don't overheat. In the datasheet, you will find some information that you can use to estimate how hot the junction inside the IC will get.
Let's look at an example. Here's a page from the IRF7739 DirectFET datasheet. I like this datasheet because it has almost all the thermal stuff on one page,...
Short Takes (EE Shanty): What shall we do with a zero-ohm resistor?
In circuit board design you often need flexibility. It can cost hundreds or thousands of dollars to respin a circuit board, so I need flexibility for two main reasons:
- sometimes it's important to be able to use one circuit board design to serve more than one purpose
- risk reduction: I want to give myself the option to add in or leave out certain things when I'm not 100% sure I'll need them.
And so we have jumpers and DIP switches and zero-ohm resistors:
Jumpers and...
Another 10 Circuit Components You Should Know
It's that time again to review all the oddball goodies available in electronic components. These are things you should have in your bag of tricks when you need to design a circuit board. If you read my previous posts and were looking forward to more, this article's for you!
1. Bus switches
I can't believe I haven't mentioned bus switches before. What is a bus switch?
There are lots of different options for switches:
- mechanical switch / relay: All purpose, two...
Have You Ever Seen an Ideal Op-Amp?
Somewhere, along with unicorns and the Loch Ness Monster, lies a small colony of ideal op-amps. Op-amp is short for operational amplifier, and we start our education on them by learning about these mythical beasts, which have the following properties:
- Infinite gain
- Infinite input impedance
- Zero output impedance
And on top of it all, they will do whatever it takes to change their output in order to make their two inputs equal.
But they don't exist. Real op-amps have...
A Useful Current Profiling Method
In one of my recent projects, I had to capture the dynamic current profile of a short-range wireless embedded platform for a number of operation scenarios. Due to the dynamic nature of the current consumption involved, I was unable to use a standard voltmeter for this job. On the time axis, I needed a minimum resolution of 1 millisecond and the accuracy of the current measurement was supposed to be better than 2 mA. This task would be a piece of cake with a Digital Storage...
Wye Delta Tee Pi: Observations on Three-Terminal Networks
Today I’m going to talk a little bit about three-terminal linear passive networks. These generally come in two flavors, wye and delta.
Why Wye?The town of Why, Arizona has a strange name that comes from the shape of the original road junction of Arizona State Highways 85 and 86, which was shaped like the letter Y. This is no longer the case, because the state highway department reconfigured the intersection
How to Analyze a Differential Amplifier
There are a handful of things that you just have to know if you do any decent amount of electronic circuit design work. One of them is a voltage divider. Another is the behavior of an RC filter. I'm not going to explain these two things or even link to a good reference on them — either you already know how they work, or you're smart enough to look it up yourself.
The handful of things also includes some others that are a little more interesting to discuss. One of them is this...
Voltage Drops Are Falling on My Head: Operating Points, Linearization, Temperature Coefficients, and Thermal Runaway
Today’s topic was originally going to be called “Small Changes Caused by Various Things”, because I couldn’t think of a better title. Then I changed the title. This one’s not much better, though. Sorry.
What I had in mind was the Shockley diode equation and some other vaguely related subjects.
My Teachers Lied to MeMy introductory circuits class in college included a section about diodes and transistors.
The ideal diode equation is...
Short Takes (EE Shanty): What shall we do with a zero-ohm resistor?
In circuit board design you often need flexibility. It can cost hundreds or thousands of dollars to respin a circuit board, so I need flexibility for two main reasons:
- sometimes it's important to be able to use one circuit board design to serve more than one purpose
- risk reduction: I want to give myself the option to add in or leave out certain things when I'm not 100% sure I'll need them.
And so we have jumpers and DIP switches and zero-ohm resistors:
Jumpers and...
First Steps in OrCAD 16 [Capture]
Hello community, I know that in last posts I have been writting about the Software. But what about Hardware? In last months I have been dealing with it, exactly with OrCAD 16. And I will explain how to build a PCB in 2 articles. For begginers could be a good and easy guide.
This article explains the part for the designing of the schematic, and in the next one which i will explain the layout part.
The first stuff you must known about OrCAD is that it is not an unique tool for...
Hot Fun in the Silicon: Thermal Testing with Power Semiconductors
Here's a trick that is useful the next time you do thermal testing with your MOSFETs or IGBTs.
Thermal testing?!
Yes, that's right. It's important to make sure your power transistors don't overheat. In the datasheet, you will find some information that you can use to estimate how hot the junction inside the IC will get.
Let's look at an example. Here's a page from the IRF7739 DirectFET datasheet. I like this datasheet because it has almost all the thermal stuff on one page,...
A Useful Current Profiling Method
In one of my recent projects, I had to capture the dynamic current profile of a short-range wireless embedded platform for a number of operation scenarios. Due to the dynamic nature of the current consumption involved, I was unable to use a standard voltmeter for this job. On the time axis, I needed a minimum resolution of 1 millisecond and the accuracy of the current measurement was supposed to be better than 2 mA. This task would be a piece of cake with a Digital Storage...
Make Your Own MCU Boards (2023 Teardown Conference)
Ditch the development boards! Products like the Nucleo development boards serve a wonderful purpose, but they’re ill-suited for projects that need to be small and cheap, such as hobby projects or products just beginning a production run. In this talk (a recording from the 2023 Teardown Conference), you’ll learn how to put a microcontroller or other custom circuit on a PCB a little larger than a stick of gum for less than $3 a board.
Layout recomendations and tips for best performance against EMC
When making the layout of the circuit diagram, it is interesting to perform a preliminary analysis of several issues in order to minimize problems arising from electromagnetic compatibility.The analysis consists in:
Identify / Analyze components: This section will analyze the integrated components, as well as any recommendations it may have the manufacturer. We must also analyze the encapsulation possibilities which have the component.
Getting smacked by the long tail of poor design habits
In the 80’s I did a fair amount of consulting and enjoyed it greatly.
I would come in, hear what it was the person hiring me wanted; meet with the people that I needed to work with and proceed to toss together a design, parts list, and program. Sometimes I would work with them to get a board into production. I knew my chips and code and could make all kinds of amazing toys.
One of my biggest repeat customers eventually offered a good salary at the same time that my wife was feeling...