Hello ,
I was testing out H-JTAG on my LPC2138 system, and loaded one of my
working hex files using H-JTAG.
I think I must have over written the Philips bootloader in the
process.Now I cannot flash using the WinARM or philips ISP tool.
Is it possible to get the bootloader going again ?
I read one thread of klemen_dovrtel on this issue which ended abruptly.
Are the bootimage files uploaded by Jayasooriah same as a bootloader ?
" Twentyone " had some bootloader files on his H-JTAG site , but I was
not able to figure out how to use them.
Any support would be appreciated.
Cheers
Thomas
LPC2138 Bootloader
Started by ●December 8, 2007
Reply by ●December 8, 20072007-12-08
Hi Dave,
Thanks for that.There was a problem in the ISP part of my circuit.
No trashing of the bootloader as you figured out
Thanks again.
Thomas
--- In l..., "derbaier" wrote:
>
> --- In l..., "thos_fernando" wrote:
> >
> > Hello ,
> >
> > I was testing out H-JTAG on my LPC2138 system, and loaded one of my
> > working hex files using H-JTAG.
> > I think I must have over written the Philips bootloader in the
> > process.Now I cannot flash using the WinARM or philips ISP tool.
> > Is it possible to get the bootloader going again ?
> > I read one thread of klemen_dovrtel on this issue which ended
abruptly.
> > Are the bootimage files uploaded by Jayasooriah same as a bootloader ?
> > " Twentyone " had some bootloader files on his H-JTAG site , but I was
> > not able to figure out how to use them.
> >
> > Any support would be appreciated.
> >
> > Cheers
> > Thomas
> >
> You can get the LPC2138 bootloader here:
>
http://www.standardics.nxp.com/support/documents/microcontrollers/?scope=LPC2000&type=software
>
> I would think that it is pretty unlikely that the H-JTAG FLASHER could
> have trashed the NXP bootloader in your LPC2138 though.
>
> --Dave
>
Thanks for that.There was a problem in the ISP part of my circuit.
No trashing of the bootloader as you figured out
Thanks again.
Thomas
--- In l..., "derbaier" wrote:
>
> --- In l..., "thos_fernando" wrote:
> >
> > Hello ,
> >
> > I was testing out H-JTAG on my LPC2138 system, and loaded one of my
> > working hex files using H-JTAG.
> > I think I must have over written the Philips bootloader in the
> > process.Now I cannot flash using the WinARM or philips ISP tool.
> > Is it possible to get the bootloader going again ?
> > I read one thread of klemen_dovrtel on this issue which ended
abruptly.
> > Are the bootimage files uploaded by Jayasooriah same as a bootloader ?
> > " Twentyone " had some bootloader files on his H-JTAG site , but I was
> > not able to figure out how to use them.
> >
> > Any support would be appreciated.
> >
> > Cheers
> > Thomas
> >
> You can get the LPC2138 bootloader here:
>
http://www.standardics.nxp.com/support/documents/microcontrollers/?scope=LPC2000&type=software
>
> I would think that it is pretty unlikely that the H-JTAG FLASHER could
> have trashed the NXP bootloader in your LPC2138 though.
>
> --Dave
>
Reply by ●December 12, 20072007-12-12
On Sat, 8 Dec 2007, derbaier wrote:
> I would think that it is pretty unlikely that the H-JTAG FLASHER could
> have trashed the NXP bootloader in your LPC2138 though.
That's a masked ROM, right?
-Kenny
--
Kenneth R. Crudup Sr. SW Engineer, Scott County Consulting, Los Angeles
O: 3630 S. Sepulveda Blvd. #138, L.A., CA 90034-6809 (888) 454-8181
> I would think that it is pretty unlikely that the H-JTAG FLASHER could
> have trashed the NXP bootloader in your LPC2138 though.
That's a masked ROM, right?
-Kenny
--
Kenneth R. Crudup Sr. SW Engineer, Scott County Consulting, Los Angeles
O: 3630 S. Sepulveda Blvd. #138, L.A., CA 90034-6809 (888) 454-8181