hc12 sci PROBLEM

On Jul 5, 12:59 pm, Jessie <freshfreef...@gmail.com> wrote:

>I use the full simulation s19 file to load to the hc12evb chip

You probably shouldn't be loading a simulation hex file into an actual
chip.

Codewarrior projects support multiple targets.  Change the target to
one suitable for your BDM pod or serial loader.

As for the chip versions, you'll need to check that the special
function registers for the ADC and the serial are all at the proper
addresses for the chip you have.

To cs_post,

Thanks for your continous help. I tried the SCI port again and
again,it just cannot function well to when apply to the ATD converter.
Can anyone help me to check the code below? First I initiate the SCI
port and the ATD converter, once the comment string is transfered,
I'll let SCI go and read the ATD result from the ADR register. Do I
need to set up some breakpoint or synchronization during the
programing?


ORG                  $0800
FCB                  $07
ORG                  $820



;ATD registers;
ATDCTL1 EQU   $0061
ATDCTL2 EQU   $0062                    ;used to select power-up mode;
(ADPU,AFFC,AWAI,0,0,0,ASCIE,ASCIF)
ATDCTL3 EQU   $0063	               ;used to select freeze control;
(0,0,0,0,0,0,FRZ1,FRZ2)
ATDCTL4 EQU   $0064	               ;used to select sample time bit and
total divisor
ATDCTL5 EQU   $0065                    ;used to select conversion
modes, channels and initiate conversions
                                       ;(0,S8CM,SCAN,MULT,CD,CC,CB,CA)

ADR2H   EQU   $0074                    ;Result registers

ATDSTATH EQU  $0066                    ;SCF implemented, sequence
complete flag


;SCI registers;
SC0BDL  EQU  $00C1
SC0CR1  EQU  $00C2
SC0CR2  EQU  $00C3
SC0SR1  EQU  $00C4
SC0DRH  EQU  $00C6
SC0DRL  EQU  $00C7

	;ORG     $0D00
MAIN:   ;LDAB   #$FF
        BSR    INIT_SCI                     ;Branch to INIT to
initialize ATD
	BSR    TRANS
	                  ;Branch to CONVERT for ATD conversion
	BSR    INIT
	BSR    CONVERT

	BSR    TRANS2
	;BSR   DELAY2
        ;DECB
        BSR    DELAY2
	BSR    MAIN

        SWI
	END

;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
;subroutine to initiate adc;
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;

INIT    LDAA   #$80                     ;Load $80 to ATDCTL2 to power
up ATD
	STAA   ATDCTL2

	BSR    DELAY                    ;Delay 100us for the capacitors
charging

	LDAA   #$00                     ;Load $00 to ATDCTL3 to select the
continue conversion mode,NO FREEZE
	STAA   ATDCTL3

	LDAA   #$01                     ;8-bit operation, 2 ATD clock
	STAA   ATDCTL4                  ;total divisor as 4
	RTS

;;;;;;;;;;;;;;;;;;;;;;;;;;
;SUBROURTINE DELAY 100us;
;;;;;;;;;;;;;;;;;;;;;;;;;;

        LDAA   #$C8

DELAY:  DECA
        BNE    DELAY
	RTS

	JMP    INIT

;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
;subroutine convert;
;-----------------------------------;
;set up ATD, make single conversion and store the result to a memory
location.
;configure and start ATD conversion
;Analog input signal: on port AD6
;convert:using single channel, non-continuous
;The result will be located in ADR2H

CONVERT:LDAA   #$06                     ;Initiate ATD scan=0, mult=0,
pad6
	STAA   ATDCTL5
WTCONV  NOP
        BRCLR  ATDSTATH,#$80,WTCONV     ;Wait for sequitence complet
flag

        LDD    ADR2H                    ;Load conversion result from
ADR2H,results in accumulator D
	STD    READING                  ;STORE D IN LOCATION READING
	BRA    CONVERT                  ;Contiously updates results

	RTS
;;;;;;;;;;;;;;;;;;;;;;;;;;
;SUBROURTINE DELAY 100us;
;;;;;;;;;;;;;;;;;;;;;;;;;;


DELAY2	LDY   #$FFFF
L1      DEY
        BNE   L1

	DEC   $800
	BNE   DELAY2
	RTS




;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
;SUBROUTINE TO INITIATE SCI;
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
INIT_SCI:TPA                    ;transfer CCR to A accumulator
         ORAA  #$10              ;Ored A with #$10 to set I bit
         TAP                     ;Transfer A to CCR

	MOVB   #$34,SC0BDL       ;SET baud=9600
	MOVB   #$00,SC0CR1       ;Initialize for 8-bit data format

	MOVB   #$08,SC0CR2       ;set for no Ints, and transmitter enabled
SC1CR2
        LDX    #COMMENT           ;TRANSFER THE COMMENT

        LDY    #READING           ;TRANSFER THE READING RESULT
	LDAA   SC0SR1            ;1st step to clear TDRE flag:read SC0SR1
	STD    SC0DRH            ;2nd step to clear TDRE flag: write SC0DR
register
	RTS
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
;SUBROUTINE TO TRANSMIT THE DATA STORED IN X;
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
TRANS  NOP
       BRCLR   SC0SR1,#$80,TRANS      ;Wait for TDRE flag

       MOVB    1,X+,SC0DRL

       CPX     #$0B12
       BNE     TRANS

       RTS


TRANS2 NOP
       BRCLR   SC0SR1,#$80,TRANS2

       MOVB    1,Y+,SC0DRL
       CPY     #$0B16
       BNE     TRANS2

       RTS




;;;;;;;;;;;;;;;;;;;;;;;
;Display the answer;
;;;;;;;;;;;;;;;;;;;;;;;
	ORG    $0B00

COMMENT FCC    'THE result IS'           ;location ended at $0B0Ddddd
        FCB    $20                   ;location ended at $0B0F
	;FCC    'PLEASE SHOW RESULT'     ;location ended at $B21
	;FCB    $0D,$0A                  ;location ended at $B23
;EOT    FCB    $04	                 ;location ended at $0B10
	;DISPLAY THE NUMBER, LOCATION AT $0905;

READING RMB     2
        FCB     $41
	FCB     $0D,$0A
;DATA    FCC    'NEXT LENGTH'
;        FCB     $0D,$0A
;EOT2    FCB     $04

Jessie