Hi All! I am newbie to rabbit Core Modules and seeking kind help from all experienced rabbit core experts in the group. I opt for RCM2200 ...

Hi All! I am newbie to rabbit Core Modules and seeking kind help from all experienced rabbit core experts in the group. I opt for RCM2200 module to embed communcation over LAN with my device with least programming overhead. So, I purchased RCM2200 module with its programming cable. I developed my own board for placing RCM2200 on it. I have Dynamic C 7.

Hi all, can I use Dymanic C 10 with my old project with rabbit 2000 ? (RCM2200) or are there any new module pin compatible with RCM2200...

Hi all, can I use Dymanic C 10 with my old project with rabbit 2000 ? (RCM2200) or are there any new module pin compatible with RCM2200 ? Regards, ricardo ------------------------------------

I have an app for the RCM2200. There is clearly a battery position marked on the upper surface (3 pins, 25mm spacing). I will need battery...

I have an app for the RCM2200. There is clearly a battery position marked on the upper surface (3 pins, 25mm spacing). I will need battery backup and it would be easy to add it to the CORE. Any idea which battery fits? I found a cr2032 mfr that looks close. Thanks in advance, David

Hi, I am looking for information and samples for design a MODBUS TCP system using a RCM2200. Any samples or links are welcome. Thanks in...

Hi, I am looking for information and samples for design a MODBUS TCP system using a RCM2200. Any samples or links are welcome. Thanks in advance, Luis Briones

I am trying to set up a PCF8591 A/D converter with my RCM2200 rabbit. I altered I2C.LIB to use bits 3 and 4 (this was the only alteration...

I am trying to set up a PCF8591 A/D converter with my RCM2200 rabbit. I altered I2C.LIB to use bits 3 and 4 (this was the only alteration I did there). I have confirmed that the start and write routines all happen in correct order by using breakpoints and single steps. All appears ok but the 8591 doesn't pull the data pin low after I send the address. Everyt

Hi I am a final year Electronic Engineering student and my design requires me to develop a web server that will be able to monitor a ...

Hi I am a final year Electronic Engineering student and my design requires me to develop a web server that will be able to monitor a baby. I have been given the RCM2200 and the C3188A CMOS camera. I have decided to use still pictures. Does anybody have any ideas on how i might be able to do this. One of my problems is that the image size will be

hi, guys, i need your help, a want to send data let's say a value for exemple 100 using a web page and i want to display this value on the LCD...

hi, guys, i need your help, a want to send data let's say a value for exemple 100 using a web page and i want to display this value on the LCD of the rabbit ! anyone have any idea ? thanks a lot ------------------------------------ Posted by: n...@gmail.com ------------------------------------ ------------------------------------ Yahoo Groups Links To visit your group on the we

I'm working with an RCM2200. Is it possible to pull a program out of a rabbit if it is already programmed?

I'm working with an RCM2200. Is it possible to pull a program out of a rabbit if it is already programmed?

Dear Folks, It's my turn to pay back for the turtle, as my RCM2200 were running all day long. I've got some questions to ask, if you...

Dear Folks, It's my turn to pay back for the turtle, as my RCM2200 were running all day long. I've got some questions to ask, if you would please to answer, I would really appreciate that. Here are the questions. 1. I've been working on BitRdPort, BitWrPort, WrPort and RdPort functions for several days, but they didn't work.(Note that, I'

Hello all i could not understand this doprnt() function. I have DC9.21 but i can't find its docs.Can any one tell me the path or give...

Hello all i could not understand this doprnt() function. I have DC9.21 but i can't find its docs.Can any one tell me the path or give correct explanation to this function. I got stuck up at RCM2200/KEYLCD.C i couldn't get this understand. Plz help me out. With Regards Phani.

Hi, I have an RCM2200 design that I suspect had problems in some occasions because the LM7805 (TO-220 with heat sink) was getting very...

Hi, I have an RCM2200 design that I suspect had problems in some occasions because the LM7805 (TO-220 with heat sink) was getting very hot. Depending on the enclosure the customer used and the ambient temperature I believe it led to some Rabbit module failures. It seemed like we got more failures during the warmer months especially from places in the country that are warmer (i.e. ...

Hi! I've been using the RCM2200 for 5+ years in a commercial product and the new RCM6750 in a current product. While the module is working...

Hi! I've been using the RCM2200 for 5+ years in a commercial product and the new RCM6750 in a current product. While the module is working fine, I'm realizing I'm asking for just a little too much from it. Specifically I have users that are pulling growing HTML web pages from multiple clients simultaneously (iPads, PCs, cell phone, etc.) and the module just can't keep up with the demand. I...

Hi all. I work for a Spanish company and we develop our equipments using RCM2200 and RCM2250 core modules as our processor. We would...

Hi all. I work for a Spanish company and we develop our equipments using RCM2200 and RCM2250 core modules as our processor. We would like to give these equipments our own MAC address, so I would like to know if it is possible (legally) and how to change the MAC address properly. Is it necessary to use the write_idblock.c function? In this case, which

Hello, I am trying to upgrade the core module in an OP7200 from an RCM2200 to an RCM2250 (equiv to OP7200B). I have tried to write a new ID...

Hello, I am trying to upgrade the core module in an OP7200 from an RCM2200 to an RCM2250 (equiv to OP7200B). I have tried to write a new ID block to the new core using the program provided by Rabbit (WriteIdBlock.c), but am given the following errors. write_idblock.c, version 2.06. ID block successfully written. Error -3 when reading ID block. When I try to read the ID block...

Hi, I am doing this internet management device that uses barcode scanner as its input. I am using PS2 connector for this project and I...

Hi, I am doing this internet management device that uses barcode scanner as its input. I am using PS2 connector for this project and I just wondered how to decode the PS2 barcode scanner? Any inputs or samples maybe? Ndo^x

Hello, I am trying to connect a RCM3400 to the Sensirion SHT11 humidity sensor. I searched the group archives and found a reference some...

Hello, I am trying to connect a RCM3400 to the Sensirion SHT11 humidity sensor. I searched the group archives and found a reference some posted code for a RCM2200, but it was no longer on site. I was curious if someone might have code for the SHT11? Phil ------------------------------------

I save some parameter such as IP address , configuration and etc in FS file system. I will save these parameters when I send a TCP command...

I save some parameter such as IP address , configuration and etc in FS file system. I will save these parameters when I send a TCP command for writing . My partner write a software on PC to polling the rabbit and write to the flash memory every time he connected ( every 5-10 min) for two years ago. Now my product was failed. I guess that flash memory was damaged. Anyone has...

Hi, It seems that my RCM3200 module has problems connecting to my 10/100 Mb 3com switch. It auto switches to 100 Mb, though it does not...

Hi, It seems that my RCM3200 module has problems connecting to my 10/100 Mb 3com switch. It auto switches to 100 Mb, though it does not establish a connection. If I use my (old) 10 Mb switch, it works ok. On the Rabbit semiconductors website I saw that there were some problems with the RCM2200 ethernet interface and a fix is available.

Simple task but I make it so difficult. I have 2 RCM2200 modules connected serially. Using port D I have TXD going to RXD, RTS going to ...

Simple task but I make it so difficult. I have 2 RCM2200 modules connected serially. Using port D I have TXD going to RXD, RTS going to CTS, GND going to GND. (pins PC0 to PC1, PC2 to PC3, etc) All connections are sound. On Rabbit A I have a continuous loop sending "HELLO" to Rabbit B. Rabbit B runs through a constant loop reading port D and printing wh

hello,      I am using the rabbit2000 board with the RCm2200. on board. I have to change the IP address in run time. I am using...

hello,      I am using the rabbit2000 board with the RCm2200. on board. I have to change the IP address in run time. I am using the sample program Ping.c for this. I am using the TCP configuration 6 for the same purpose. It change My IP Address in the run time . but the program not pining the