Consistent Overhead Byte Stuffing
Byte stuffing is a process that transforms a sequence of data bytes that may contain ‘illegal’ or ‘reserved’ values into a potentially longer sequence that contains no occurrences of those values. The extra length is referred to in this paper as the overhead of the algorithm. To date, byte stuffing algorithms, such as those used by SLIP [RFC1055], PPP [RFC1662] and AX.25 [ARRL84], have been designed to incur low average overhead but have made little effort to minimize worst case overhead. Some increasingly popular network devices, however, care more about the worst case. For example, the transmission time for ISM-band packet radio transmitters is strictly limited by FCC regulation. To adhere to this regulation, the practice is to set the maximum packet size artificially low so that no packet, even after worst case overhead, can exceed the transmission time limit. This paper presents a new byte stuffing algorithm, called Consistent Overhead Byte Stuffing (COBS), that tightly bounds the worst case overhead. It guarantees in the worst case to add no more than one byte in 254 to any packet. Furthermore, the algorithm is computationally cheap, and its average overhead is very competitive with that of existing algorithms.
Time in Wireless Embedded System
Wireless embedded networks have matured beyond academic research as industry now considers the advantages of using wireless sensors. With this growth, reliability and real-time demands increase, thus timing becomes more and more relevant. In this dissertation, we focus on the development of highly stable, low-power clock systems for wireless embedded systems. Wireless embedded networks, due to their wire-free nature, present one of the most extreme power budget design challenges in the field of electronics. Improvements in timing can reduce the energy required to operate an embedded network. However, the more accurate a time source is, the more power it consumes. To comprehensively address the time and power problems in wireless embedded systems, this dissertation studies the exploitation of dual-crystal clock architectures to combat effects of temperature induced frequency error and high power consumption of high-frequency clocks. Combining these architectures with the inherent communication capabilities of wireless embedded systems, this dissertation proposes two new technologies; (1) a new time synchronization service that automatically calibrates a local clock to changes in temperature; (2) a high-low frequency timer that allows a duty-cycled embedded system to achieve ultra low-power sleep, while keeping fine granularity time resolution offered only by high power, high frequency clocks.
Creating a State-of-the Art, Cost Effective Energy Harvesting Bluetooth® Low Energy Switch
As IoT rapidly grows into new markets such as MHealth, Agriculture 4.0, and building automation, new questions are being raised about the energy required to support its growth. Within the industry, we see a broad spectrum of power requirements.
Boosting Performance Oscilloscope Versatility, Scalability Whitepaper
Rising data communication rates are driving the need for very high-bandwidth real-time oscilloscopes in the range of 60-70 GHz. These instruments are essential for validating and debugging new designs in coherent optical modulation analysis, high energy physics research, high speed data communications and other areas. With the DPO70000SX Performance Oscilloscope series, Tektronix delivers real-time signal acquisition with an ultra-high bandwidth of 70 GHz, along with a real-time sample rate of 200 GS/s (5ps/sample resolution), making it ideal for such applications.
Creating a State-of-the Art, Cost Effective Energy Harvesting Bluetooth® Low Energy Switch
As IoT rapidly grows into new markets such as MHealth, Agriculture 4.0, and building automation, new questions are being raised about the energy required to support its growth. Within the industry, we see a broad spectrum of power requirements.
Boosting Performance Oscilloscope Versatility, Scalability Whitepaper
Rising data communication rates are driving the need for very high-bandwidth real-time oscilloscopes in the range of 60-70 GHz. These instruments are essential for validating and debugging new designs in coherent optical modulation analysis, high energy physics research, high speed data communications and other areas. With the DPO70000SX Performance Oscilloscope series, Tektronix delivers real-time signal acquisition with an ultra-high bandwidth of 70 GHz, along with a real-time sample rate of 200 GS/s (5ps/sample resolution), making it ideal for such applications.
Consistent Overhead Byte Stuffing
Byte stuffing is a process that transforms a sequence of data bytes that may contain ‘illegal’ or ‘reserved’ values into a potentially longer sequence that contains no occurrences of those values. The extra length is referred to in this paper as the overhead of the algorithm. To date, byte stuffing algorithms, such as those used by SLIP [RFC1055], PPP [RFC1662] and AX.25 [ARRL84], have been designed to incur low average overhead but have made little effort to minimize worst case overhead. Some increasingly popular network devices, however, care more about the worst case. For example, the transmission time for ISM-band packet radio transmitters is strictly limited by FCC regulation. To adhere to this regulation, the practice is to set the maximum packet size artificially low so that no packet, even after worst case overhead, can exceed the transmission time limit. This paper presents a new byte stuffing algorithm, called Consistent Overhead Byte Stuffing (COBS), that tightly bounds the worst case overhead. It guarantees in the worst case to add no more than one byte in 254 to any packet. Furthermore, the algorithm is computationally cheap, and its average overhead is very competitive with that of existing algorithms.
Time in Wireless Embedded System
Wireless embedded networks have matured beyond academic research as industry now considers the advantages of using wireless sensors. With this growth, reliability and real-time demands increase, thus timing becomes more and more relevant. In this dissertation, we focus on the development of highly stable, low-power clock systems for wireless embedded systems. Wireless embedded networks, due to their wire-free nature, present one of the most extreme power budget design challenges in the field of electronics. Improvements in timing can reduce the energy required to operate an embedded network. However, the more accurate a time source is, the more power it consumes. To comprehensively address the time and power problems in wireless embedded systems, this dissertation studies the exploitation of dual-crystal clock architectures to combat effects of temperature induced frequency error and high power consumption of high-frequency clocks. Combining these architectures with the inherent communication capabilities of wireless embedded systems, this dissertation proposes two new technologies; (1) a new time synchronization service that automatically calibrates a local clock to changes in temperature; (2) a high-low frequency timer that allows a duty-cycled embedded system to achieve ultra low-power sleep, while keeping fine granularity time resolution offered only by high power, high frequency clocks.
Consistent Overhead Byte Stuffing
Byte stuffing is a process that transforms a sequence of data bytes that may contain ‘illegal’ or ‘reserved’ values into a potentially longer sequence that contains no occurrences of those values. The extra length is referred to in this paper as the overhead of the algorithm. To date, byte stuffing algorithms, such as those used by SLIP [RFC1055], PPP [RFC1662] and AX.25 [ARRL84], have been designed to incur low average overhead but have made little effort to minimize worst case overhead. Some increasingly popular network devices, however, care more about the worst case. For example, the transmission time for ISM-band packet radio transmitters is strictly limited by FCC regulation. To adhere to this regulation, the practice is to set the maximum packet size artificially low so that no packet, even after worst case overhead, can exceed the transmission time limit. This paper presents a new byte stuffing algorithm, called Consistent Overhead Byte Stuffing (COBS), that tightly bounds the worst case overhead. It guarantees in the worst case to add no more than one byte in 254 to any packet. Furthermore, the algorithm is computationally cheap, and its average overhead is very competitive with that of existing algorithms.
Time in Wireless Embedded System
Wireless embedded networks have matured beyond academic research as industry now considers the advantages of using wireless sensors. With this growth, reliability and real-time demands increase, thus timing becomes more and more relevant. In this dissertation, we focus on the development of highly stable, low-power clock systems for wireless embedded systems. Wireless embedded networks, due to their wire-free nature, present one of the most extreme power budget design challenges in the field of electronics. Improvements in timing can reduce the energy required to operate an embedded network. However, the more accurate a time source is, the more power it consumes. To comprehensively address the time and power problems in wireless embedded systems, this dissertation studies the exploitation of dual-crystal clock architectures to combat effects of temperature induced frequency error and high power consumption of high-frequency clocks. Combining these architectures with the inherent communication capabilities of wireless embedded systems, this dissertation proposes two new technologies; (1) a new time synchronization service that automatically calibrates a local clock to changes in temperature; (2) a high-low frequency timer that allows a duty-cycled embedded system to achieve ultra low-power sleep, while keeping fine granularity time resolution offered only by high power, high frequency clocks.
Boosting Performance Oscilloscope Versatility, Scalability Whitepaper
Rising data communication rates are driving the need for very high-bandwidth real-time oscilloscopes in the range of 60-70 GHz. These instruments are essential for validating and debugging new designs in coherent optical modulation analysis, high energy physics research, high speed data communications and other areas. With the DPO70000SX Performance Oscilloscope series, Tektronix delivers real-time signal acquisition with an ultra-high bandwidth of 70 GHz, along with a real-time sample rate of 200 GS/s (5ps/sample resolution), making it ideal for such applications.
Creating a State-of-the Art, Cost Effective Energy Harvesting Bluetooth® Low Energy Switch
As IoT rapidly grows into new markets such as MHealth, Agriculture 4.0, and building automation, new questions are being raised about the energy required to support its growth. Within the industry, we see a broad spectrum of power requirements.
