PID Without a PhD
PID (proportional, integral, derivative) control is not as complicated as it sounds. Follow these simple implementation steps for quick results.
Introduction to Embedded Systems - A Cyber-Physical Systems Approach
This book strives to identify and introduce the durable intellectual ideas of embedded systems as a technology and as a subject of study. The emphasis is on modeling, design, and analysis of cyber-physical systems, which integrate computing, networking, and physical processes. This book is intended for students at the advanced undergraduate level or the introductory graduate level, and for practicing engineers and computer scientists who wish to understand the engineering principles of embedded systems.
Lessons in Electric Circuits - Volume III - Semiconductor
This book covers all of the common semiconductor devices and their principles of operation. However, the true value of this reference is in the fact that it provides key circuits and applications where they come in handy. A few of the devices that are covered in this book are Bipolar junction transistors, diodes, JFETs, thyristors, OPAMPs and FETs. This book will be a good reference in your library that has a clear style of explanation.
A Multithreaded Real-time Robot for Embedded Design Space Exploration
This thesis introduces an autonomous robot platform for real-time scheduling exper- imentation and benchmark suite to evaluate real-time optimizations and apply modern task scheduling methods. It makes two contributions. First, it presents a reference hardware and software design for a line-following, obstacle-avoiding and maze-solving robot. This robot is based on a small commercially-available product. The software is structured as a multithreaded real- time system for use in evaluating scheduling approaches for cost-sensitive and resource- constrained applications. Second, it provides a detailed design space exploration showing the costs (processor speed and memory) of di erent scheduling approaches (static vs. dynamic and non-preemptive vs. preemptive). It also measures and analyzes each task's timing information and explores the mini- mum microcontroller clock speed under di erent scheduling approaches.
Interrupts, Low Power Modes and Timer A
This document contains a lot of what you need to know to get the most out of the MSP430. The MSP430 line is renowned for it's low power usage, and to really utilize it well you have to architect your software to be an interrupt driven device that utilizes the low power modes.
Microcontroller Programming and Interfacing
Chapter 7 of the book: Introduction to Mechatronics and Measurement Systems
Real-time Image Processing on Low Cost Embedded Computers
In 2012 a federal mandate was imposed that required the FAA to integrate unmanned aerial systems (UAS) into the national airspace (NAS) by 2015 for civilian and commercial use. A significant driver for the increasing popularity of these systems is the rise in open hardware and open software solutions which allow hobbyists to build small UAS at low cost and without specialist equipment. This paper describes our work building, evaluating and improving performance of a vision-based system running on an embedded computer onboard such a small UAS. This system utilises open source software and open hardware to automatically land a multi-rotor UAS with high accuracy. Using parallel computing techniques, our final implementation runs at the maximum possible rate of 30 frames per second. This demonstrates a valid approach for implementing other real-time vision based systems onboard UAS using low power, small and economical embedded computers.
Getting Started with C Programming for the ATMEL AVR Microcontrollers
This tutorial provides information on the tool and the basic steps for programming the Atmel AVR microcontrollers using C. It is aimed at people who are new to this family of microcontrollers. The Atmel STK500 development board and the ATmega16 chip are used in this tutorial; however, it is easy to adopt the information given here for other AVR chips.
An Embedded Object Approach to Embedded System Development
Building an embedded system from an idea to a product is a slow and expensive process requiring a lot of expertise. Depending on the developer’s expertise, the required quantity and price level of the final product, and the time and money available for development, the developer can build a device from different granularity of components, ranging from ready-made platforms, kits, and modules to individual components. Generally, solutions requiring less expertise, time and money produce products with higher production costs. The main contribution of this thesis is the EOC (Embedded Object Concept) and Atomi II Framework. EOC utilizes common object-oriented methods used in software by applying them to small electronic modules, which create complete functional entities. The conceptual idea of the embedded objects is implemented with the Atomi II framework, which contains several techniques for making the EOC a commercially feasible implementation. The EOC and the Atomi II Framework decreases the difficulty level of making embedded systems by enabling a use of ready-made modules to build systems. It enables automatic conversion of a device made from such modules into an integrated PCB, lowering production costs compared to other modular approaches. Furthermore, it also enables an automatic production tester generation due to its modularity. These properties lower the number of skills required for building an embedded system and quicken the path from an idea to a commercially applicable device. A developer can also build custom modules of his own if he possesses the required expertise. The test cases demonstrate the Atomi II Framework techniques in real world applications, and demonstrate the capabilities of Atomi objects. According to our test cases and estimations, an Atomi based device becomes approximately 10% more expensive than a device built from individual components, but saves up to 50% time, making it feasible to manufacture up to 10-50k quantities with this approach.
Introduction to Microcontrollers
This text has been developed for the introductory courses on microcontrollers taught by the Institute of Computer Engineering at the Vienna University of Technology. It introduces undergraduate students to the field of microcontrollers – what they are, how they work, how they interface with their I/O components, and what considerations the programmer has to observe in hardware-based and embedded programming. This text is not intended to teach one particular controller architecture in depth, but should rather give an impression of the many possible architectures and solutions one can come across in today’s microcontrollers. We concentrate, however, on small 8-bit controllers and their most basic features, since they already offer enough variety to achieve our goals.
Enhanced Sample Rate Mode Measurement Precision
The low-noise system architecture and the tailored frequency response employed in the HDO4000A, HDO6000A, HDO8000A and MDA800A series provides the foundation for enhancing ADC sample rates through additional techniques. In this case, carefully constructed filters combined with a pristine front-end amplifier and a frequency response carefully limited to 1 GHz provide the opportunity to provide more measurement precision than would otherwise be possible. The technique utilized to achieve higher measurement precision is interpolation, and this technique is used by default as an Enhanced Sample Rate up to 10 GS/s. By integrating the Enhanced Sample Rate functionality with the normal Timebase controls for Sample Rate, Time and Acquisition Memory adjustment, the oscilloscopes are optimized for best waveform signal fidelity in all situations.
Improving Battery Management System Performance and Cost with Altera FPGAs
The purpose of this white paper is to evaluate improvements to Battery Management System (BMS) performance and cost with Altera® FPGAs. In many high-voltage battery systems, including electric vehicles, grid attached storage and industrial applications, the battery is a significant portion of the system cost, and needs to be carefully managed by a BMS to maximize battery life and to optimize charging and discharging performance. This white paper presents the BMS functional requirements for these applications and outlines existing BMS architectures. Key BMS architectural challenges are discussed and opportunities for Altera devices are identified. For each of these opportunities, the performance and cost of the existing solution are compared with Altera FPGA solutions. Altera devices provide architectural flexibility, scalability, customization, performance improvements, and system cost savings in BMS applications.
Arduino Microcontroller Guide
The Arduino microcontroller is an easy to use yet powerful single board computer that has gained considerable traction in the hobby and professional market. The Arduino is open-source, which means hardware is reasonably priced and development software is free. This guide is for students in ME 2011, or students anywhere who are confronting the Arduino for the first time. For advanced Arduino users, prowl the web; there are lots of resources.
Introduction to Arduino
The purpose of this book is to get you started on the road to creating things using micro-controllers. We will discuss only enough electronics for you to make the circuits, and only enough programming for you to get started. The focus will be on your making things. It is my hope that as you go through this book you will be flooded with ideas of things that you can make.
Guide to designing a device incorporating MEMSbased pico projection
Over the last few years, millions of products incorporating pico projection have shipped, and developers are innovating new applications for this rapidly growing display category. Ideal applications for pico projection include near eye display, interactive digital signage, head mounted display, ultra short throw (UST) TV, standalone portable projectors and embedded projection in smartphones, tablets and laptops. New uses continue to emerge; for example, you might be able imagine a design for a thermostat using a display powered by gesture recognition or interactive touch.
Real-time Image Processing on Low Cost Embedded Computers
In 2012 a federal mandate was imposed that required the FAA to integrate unmanned aerial systems (UAS) into the national airspace (NAS) by 2015 for civilian and commercial use. A significant driver for the increasing popularity of these systems is the rise in open hardware and open software solutions which allow hobbyists to build small UAS at low cost and without specialist equipment. This paper describes our work building, evaluating and improving performance of a vision-based system running on an embedded computer onboard such a small UAS. This system utilises open source software and open hardware to automatically land a multi-rotor UAS with high accuracy. Using parallel computing techniques, our final implementation runs at the maximum possible rate of 30 frames per second. This demonstrates a valid approach for implementing other real-time vision based systems onboard UAS using low power, small and economical embedded computers.
Guide to designing a device incorporating MEMS-based pico projection
Over the last few years, millions of products incorporating pico projection have shipped, and developers are innovating new applications for this rapidly growing display category. Ideal applications for pico projection include near eye display, interactive digital signage, head mounted display, ultra short throw (UST) TV, standalone portable projectors and embedded projection in smartphones, tablets and laptops. New uses continue to emerge; for example, you might be able imagine a design for a thermostat using a display powered by gesture recognition or interactive touch.
Getting Started with C Programming for the ATMEL AVR Microcontrollers
This tutorial provides information on the tool and the basic steps for programming the Atmel AVR microcontrollers using C. It is aimed at people who are new to this family of microcontrollers. The Atmel STK500 development board and the ATmega16 chip are used in this tutorial; however, it is easy to adopt the information given here for other AVR chips.
PIC Microcontrollers - Programming in C
If you haven’t done it so far then it’s high time to learn what the microcontrollers are and how they operate. Numerous illustrations and practical examples along with detailed description of the PIC16F887 will make you enjoy your work with the PIC microcontrollers
Microcontroller Programming and Interfacing
Chapter 7 of the book: Introduction to Mechatronics and Measurement Systems
PID Without a PhD
PID (proportional, integral, derivative) control is not as complicated as it sounds. Follow these simple implementation steps for quick results.
Getting Started with C Programming for the ATMEL AVR Microcontrollers
This tutorial provides information on the tool and the basic steps for programming the Atmel AVR microcontrollers using C. It is aimed at people who are new to this family of microcontrollers. The Atmel STK500 development board and the ATmega16 chip are used in this tutorial; however, it is easy to adopt the information given here for other AVR chips.
Introduction to Embedded Systems - A Cyber-Physical Systems Approach
This book strives to identify and introduce the durable intellectual ideas of embedded systems as a technology and as a subject of study. The emphasis is on modeling, design, and analysis of cyber-physical systems, which integrate computing, networking, and physical processes. This book is intended for students at the advanced undergraduate level or the introductory graduate level, and for practicing engineers and computer scientists who wish to understand the engineering principles of embedded systems.
Microcontroller Programming and Interfacing
Chapter 7 of the book: Introduction to Mechatronics and Measurement Systems
PIC Microcontrollers - Programming in C
If you haven’t done it so far then it’s high time to learn what the microcontrollers are and how they operate. Numerous illustrations and practical examples along with detailed description of the PIC16F887 will make you enjoy your work with the PIC microcontrollers
Introduction to Microcontrollers
This text has been developed for the introductory courses on microcontrollers taught by the Institute of Computer Engineering at the Vienna University of Technology. It introduces undergraduate students to the field of microcontrollers – what they are, how they work, how they interface with their I/O components, and what considerations the programmer has to observe in hardware-based and embedded programming. This text is not intended to teach one particular controller architecture in depth, but should rather give an impression of the many possible architectures and solutions one can come across in today’s microcontrollers. We concentrate, however, on small 8-bit controllers and their most basic features, since they already offer enough variety to achieve our goals.
Real-time Image Processing on Low Cost Embedded Computers
In 2012 a federal mandate was imposed that required the FAA to integrate unmanned aerial systems (UAS) into the national airspace (NAS) by 2015 for civilian and commercial use. A significant driver for the increasing popularity of these systems is the rise in open hardware and open software solutions which allow hobbyists to build small UAS at low cost and without specialist equipment. This paper describes our work building, evaluating and improving performance of a vision-based system running on an embedded computer onboard such a small UAS. This system utilises open source software and open hardware to automatically land a multi-rotor UAS with high accuracy. Using parallel computing techniques, our final implementation runs at the maximum possible rate of 30 frames per second. This demonstrates a valid approach for implementing other real-time vision based systems onboard UAS using low power, small and economical embedded computers.
Introduction to Arduino
The purpose of this book is to get you started on the road to creating things using micro-controllers. We will discuss only enough electronics for you to make the circuits, and only enough programming for you to get started. The focus will be on your making things. It is my hope that as you go through this book you will be flooded with ideas of things that you can make.
An Embedded Object Approach to Embedded System Development
Building an embedded system from an idea to a product is a slow and expensive process requiring a lot of expertise. Depending on the developer’s expertise, the required quantity and price level of the final product, and the time and money available for development, the developer can build a device from different granularity of components, ranging from ready-made platforms, kits, and modules to individual components. Generally, solutions requiring less expertise, time and money produce products with higher production costs. The main contribution of this thesis is the EOC (Embedded Object Concept) and Atomi II Framework. EOC utilizes common object-oriented methods used in software by applying them to small electronic modules, which create complete functional entities. The conceptual idea of the embedded objects is implemented with the Atomi II framework, which contains several techniques for making the EOC a commercially feasible implementation. The EOC and the Atomi II Framework decreases the difficulty level of making embedded systems by enabling a use of ready-made modules to build systems. It enables automatic conversion of a device made from such modules into an integrated PCB, lowering production costs compared to other modular approaches. Furthermore, it also enables an automatic production tester generation due to its modularity. These properties lower the number of skills required for building an embedded system and quicken the path from an idea to a commercially applicable device. A developer can also build custom modules of his own if he possesses the required expertise. The test cases demonstrate the Atomi II Framework techniques in real world applications, and demonstrate the capabilities of Atomi objects. According to our test cases and estimations, an Atomi based device becomes approximately 10% more expensive than a device built from individual components, but saves up to 50% time, making it feasible to manufacture up to 10-50k quantities with this approach.
Embedded Touchscreen Handbook
I want to add a touchscreen to my embedded product. Where do I start? That question is common nowadays. Most manufacturing companies are seeing the value – maybe the necessity – of touch screen technology. Many of them don’t have a long-term or close association with the technology, yet they expect their embedded engineers to handle the project successfully and on a tight schedule. These engineers often have questions... - How much am I going to have to learn to get the job done? - I’ve heard that LCD suppliers were not like other suppliers. But, how so? - What don’t I know that could shift the project from “exciting” to “doomed.” You have choices: Probably the three major questions that crop up when you need to add an LCD touch screen to your product are these: - Should I use a full-blown, embedded operating system, like Windows CE, CE Linux or QNX? - How much work does it take to develop an in-house LCD system from scratch? - Do I have other options? The answer to the first two questions is a resounding “maybe,” (depending on what you need to accomplish). The answer to the third question is, probably “yes.” In most cases, there is another option. Who should read this? If you are an embedded engineer who is thinking of adding a touch screen to your product, and if: - You need to know what is involved in adding color touch controls to your product. -You need to understand the risks (both known and hidden) involved in LCD technology. - Your main area of expertise is not LCD technology. - You don’t want to re-focus your time to acquire color LCD technology expertise. If you find that any of the statements above voice your concerns, you may find this paper worth reading.
