Small or fast?
Developers of software for desktop computers take code optimization for granted. Embedded developers typically need to pay much more attention to the details
Stand-by or boot-up
Many factors affect the usability of devices - a key one is how long it takes to start up.
Write Better Code with Block Diagrams and Flowcharts
Reading and writing code without architectural diagrams is like trying to follow complex instructions without any explanatory pictures: nigh impossible! By taking the time to draw out the block diagrams and flowcharts for your code, you can help identify problems before they arise and make your code easier to design, write, test, and debug. In this article, I'll briefly justify the importance of architectural drawings such as block diagrams and flowcharts and then teach you what they are and how to draw them. Using two simple examples, you'll see first-hand how these drawings can significantly amplify your understanding of a piece of code. Additionally, I'll give you a few tips for how to implement each drawing once you've completed it and I'll share with you a few neat tools to help you complete your next set of drawings.
Memory Mapped I/O in C
Interacting with memory mapped device registers is at the base of all embedded development. Let's explore what tools the C language - standard of the industry - provide the developer with to face this task.
Some Embedded System Software Design Resources
Embedded systems span many architectures and run-times, so there is no single definitive resource. This curated list brings together practical embedded-focused books by Elecia White and Jacob Beningo, general design guidance from Robert Martin, and a TDD primer by James W. Grenning, plus concrete advice on BDD-style TDD and off-target testing. Skim the list in a day, then try the techniques hands-on.
You Don't Need an RTOS (Part 4)
In this fourth (and final!) article I'll share with you the last of the inter-process communication (IPC) methods I mentioned in Part 3: mailboxes/queues, counting semaphores, the Observer pattern, and something I'm calling a "marquee". When we're done, we'll have created the scaffolding for tasks to interact in all sorts of different the ways. Additionally, I'll share with you another alternative design for a non-preemptive scheduler called a dispatch queue that is simple to conceptualize and, like the time-triggered scheduler, can help you schedule some of your most difficult task sets.
7 Essential Steps for Reducing Power Consumption in Embedded Devices
Reducing the amount of power your embedded device is consuming is not trivial. With so many devices moving to battery operations today, maximizing battery life can be the difference between a happy, raving customer and an unhappy one that ruins your company's reputation. This post explores seven steps for optimizing your embedded systems' power consumption. You'll gain insights into the steps and techniques necessary along with receiving a few resources to help you on your journey.
Parlez vous Fortran?
A look at the variety of programming languages that are [or have been] used for embedded and some thoughts on the future possibilities.
When a Mongoose met a MicroPython, part II
In the first part of this blog, we introduced this little framework to integrate MicroPython and Cesanta's Mongoose; where Mongoose runs when called by MicroPython and is able to run Python functions as callbacks for the events you decide in your event handler. Now we add MQTT to the equation, so we can subscribe to topics and publish messages right from MicroPython.
You Don't Need an RTOS (Part 3)
In this third article I'll share with you a few cooperative schedulers (with a mix of both free and commercial licenses) that implement a few of the OS primitives that the "Superduperloop" is currently missing, possibly giving you a ready-to-go solution for your system. On the other hand, I don't think it's all that hard to add thread flags, binary and counting semaphores, event flags, mailboxes/queues, a simple Observer pattern, and something I call a "marquee" to the "Superduperloop"; I'll show you how to do that in the second half of this article and the next. Although it will take a little more work than just using one of the projects above, it will give you the maximum amount of control over your system and it will let you write tasks in ways you could only dream of using an RTOS or other off-the-shelf system.
Important Programming Concepts (Even on Embedded Systems) Part IV: Singletons
Singletons are convenient but often a modularity killer, especially in embedded firmware. Jason Sachs walks through the many faces of singletons, from static members and globals to hardware registers and user-visible application singletons, and shows practical ways to avoid tight coupling. Read this for concrete embedded examples and pragmatic fixes like passing state explicitly, using interfaces or factories, and isolating unavoidable globals in a HAL.
Introduction to Microcontrollers - Driving WS2812 RGB LEDs
Mike Silva walks through a practical, cycle-counted AVR assembly implementation to bit-bang WS2812B RGB LEDs from an 8MHz AVR, hitting the chip's tight 1.25µs-per-bit timing. The post breaks down the WS2812B self-clocked protocol and GRB byte order, explains register and calling-convention choices, and includes a complete C example plus power-consumption warnings for driving LED strips.
Intel 8088 - A blast from the past
The Intel 8088 is a reminder of how hands-on early microcomputer work really was. This short retrospective looks back at wire-wrapping, perfboard construction, and assembly language programming on a board built around the 8088 and its support chips. It is a fun contrast to today’s Raspberry Pi era, where far more performance comes in a sealed package you can’t build yourself.
You Don't Need an RTOS (Part 3)
In this third article I'll share with you a few cooperative schedulers (with a mix of both free and commercial licenses) that implement a few of the OS primitives that the "Superduperloop" is currently missing, possibly giving you a ready-to-go solution for your system. On the other hand, I don't think it's all that hard to add thread flags, binary and counting semaphores, event flags, mailboxes/queues, a simple Observer pattern, and something I call a "marquee" to the "Superduperloop"; I'll show you how to do that in the second half of this article and the next. Although it will take a little more work than just using one of the projects above, it will give you the maximum amount of control over your system and it will let you write tasks in ways you could only dream of using an RTOS or other off-the-shelf system.
Scorchers, Part 3: Bare-Metal Concurrency With Double-Buffering and the Revolving Fireplace
Jason Sachs presents a practical, low-overhead concurrency pattern for tiny bare-metal systems where an ISR (Speedy) must safely exchange data with a nonreal-time main loop (Poky). He describes the "revolving fireplace", a double-buffering variant that swaps ownership of two shared memory regions, and walks through C examples, atomic/volatile considerations, and testing strategies so you can implement it on RAM-constrained MCUs.
Finite State Machines (FSM) in Embedded Systems (Part 2) - Simple C++ State Machine Engine
When implementing state machines in your project it is an advantage to rely on a tried and tested state machine engine. This component is reused for every kind of application and helps the developer focus on the domain part of the software. In this article, the design process that turns a custom C++ code into a finite-state machine engine is fully described with motivations and tradeoffs for each iteration.
On hardware state machines: How to write a simple MAC controller using the RP2040 PIOs
Hardware state machines are nice, and the RP2040 has two blocks with up to four machines each. Their instruction set is limited, but powerful, and they can execute an instruction per cycle, pushing and popping from their FIFOs and shifting bytes in and out. The Raspberry Pi Pico does not have an Ethernet connection, but there are many PHY boards available… take a LAN8720 board and connect it to the Pico; you’re done. The firmware ? Introducing Mongoose…
You Don't Need an RTOS (Part 4)
In this fourth (and final!) article I'll share with you the last of the inter-process communication (IPC) methods I mentioned in Part 3: mailboxes/queues, counting semaphores, the Observer pattern, and something I'm calling a "marquee". When we're done, we'll have created the scaffolding for tasks to interact in all sorts of different the ways. Additionally, I'll share with you another alternative design for a non-preemptive scheduler called a dispatch queue that is simple to conceptualize and, like the time-triggered scheduler, can help you schedule some of your most difficult task sets.
Using the C language to program the am335x PRU
Assembly-language PRU development is tedious and error prone, so Fabien Le Mentec shows how to use TI's PRU C toolchain to simplify the workflow. He walks through installing the CGT package, integrating the compiler with a modified prussdrv loader to honor the _c_int00 start symbol, and provides a BeagleBone Black example with build scripts and sources on GitHub. The post also covers inline assembly constraints and code-size tradeoffs.
A Beginner's Guide to Embedded Systems
Embedded systems are everywhere, and this guide gives a practical, project-first roadmap for beginners. It explains what embedded systems are, the typical constraints you will face, and a clear learning sequence: circuit fundamentals, digital logic, C, and microcontrollers before moving on to RTOS or embedded Linux. The post also recommends hands-on dev boards and student clubs to accelerate real-world skills.
Visual Studio Code Extensions for Embedded Software Development
Visual Studio Code can be a solid embedded development environment, if you equip it with the right extensions. Jacob Beningo walks through tools for Cortex-M debugging, register and RTOS inspection, build system support, formatting, linting, and vendor-specific workflows. It is a practical tour of the extensions that help VS Code feel much less like a general-purpose editor and more like an embedded IDE.
++i and i++ : what’s the difference?
Although the ++ and -- operators are well known, there are facets of their operation and implementation that are less familiar to many developers.
How to Build a Fixed-Point PI Controller That Just Works: Part II
Jason Sachs walks through practical, battle-tested rules for implementing PI controllers in fixed-point arithmetic. He explains Q-format choices, why the integrator needs extra fractional bits, and why scale-then-integrate simplifies design. The post also covers proportional gain scaling, saturation and anti-windup, and common C pitfalls that cause overflow or lost resolution on 16/32-bit microcontrollers.
Introduction to Microcontrollers - Button Matrix & Auto Repeating
Wiring every button to its own GPIO gets expensive fast, so Mike Silva shows how to read a 4x4 keypad with only eight pins using matrix scanning. He then builds the raw scan into a debounced state machine, adds auto-repeat, and even extends it to a two-stage repeat rate. The result is a practical, code-heavy walkthrough for turning a keypad into clean button events on AVR and STM32.
You Don't Need an RTOS (Part 1)
In this first article, we'll compare our two contenders, the superloop and the RTOS. We'll define a few terms that help us describe exactly what functions a scheduler does and why an RTOS can help make certain systems work that wouldn't with a superloop. By the end of this article, you'll be able to: - Measure or calculate the deadlines, periods, and worst-case execution times for each task in your system, - Determine, using either a response-time analysis or a utilization test, if that set of tasks is schedulable using either a superloop or an RTOS, and - Assign RTOS task priorities optimally.
Finite State Machines (FSM) in Embedded Systems (Part 1) - There's a State in This Machine!
An introduction to state machines and their implementation. Working from an intuitive definition of the state machine concept, we will start with a straightforward implementation then we evolve it into a more robust and engineered solution.
Modern C++ in Embedded Development: (Don't Fear) The ++
While C is still the language of choice for embedded development, the adoption of C++ has grown steadily. Yet, reservations about dynamic memory allocation and fears of unnecessary code bloat have kept many in the C camp. This discourse aims to explore the intricacies of employing C++ in embedded systems, negotiating the issues of dynamic memory allocation, and exploiting the benefits of C++ offerings like std::array and constexpr. Moreover, it ventures into the details of the zero-overhead principle and the nuanced distinctions between C and C++. The takeaway? Armed with the right knowledge and a careful approach, C++ can indeed serve as a powerful, safer, and more efficient tool for embedded development.
Cortex-M Exception Handling (Part 1)
This article describes how Cortex-M processors handle interrupts and, more generally, exceptions, a concept that plays a central role in the design and implementation of most embedded systems.
Linear Feedback Shift Registers for the Uninitiated, Part XVI: Reed-Solomon Error Correction
Jason Sachs demystifies Reed-Solomon codes with hands-on examples and pragmatic tips for embedded engineers. The article shows why RS encoding is just polynomial division in GF(2^m), why decoding is mathematically heavier, and how to implement encoders in Python and in C-friendly form using LFSRs and table-driven methods. Read this for working code, generator-polynomial examples, and an embedded-minded view of RS practicalities.
Important Programming Concepts (Even on Embedded Systems) Part IV: Singletons
Singletons are convenient but often a modularity killer, especially in embedded firmware. Jason Sachs walks through the many faces of singletons, from static members and globals to hardware registers and user-visible application singletons, and shows practical ways to avoid tight coupling. Read this for concrete embedded examples and pragmatic fixes like passing state explicitly, using interfaces or factories, and isolating unavoidable globals in a HAL.
