Sign in
Search Comp.Arch.Embedded
embedded by Keywords
68HC11 | 68HC12 | 8051 | 8052 | ARM | ARM7 | Asic | AT91 | AT91RM9200 | Atmel | AVR | AVRStudio | Bootloader | CFP | CompactFlash | Cygnal | Cypress | Dataflash | DSP | eCos | EEPROM | Embedded Linux | Emulator | Endian | Ethernet | Firewire | FPGA | Freescale | GCC | GNUARM | GSM | H8 | HDLC | I2C | Infineon | Interrupts | Java | JTAG | LCD | LED | LPC2000 | MCU | Microchip | MMC | MPLAB | MSP430 | PC104 | PCB | PCI | PCMCIA | PowerPC | Rabbit | RS232 | RS485 | RTOS | SBC | SDRAM | Sensor | SPI | STK500 | UART | UML | USART | USB | Verilog | VHDL | VxWorks | Xilinx
Ads
Discussion Groups
See Also
PC104
Comp.Arch.Embedded is a worldwide Usenet news group that is used to discuss various aspects of Embedded Systems development.
We found 136 threads matching "pc104"
You are looking at page 1 of 4.
The most relevant threads are listed first
Pc104
adi - 2004-02-19 04:20:00
F.Y.I
Excuse me for my little knowledge in pc104.
What is the easiest way to communicate between a pc104 and a ordinary
pc, is it possible by pci slot ?
In order to do that do I need the pc104+ ?
thanks
...
PC104-FPGA newbie questions
inova - 2005-10-18 23:12:00
Hello - I'm venturing into a PC104 project and have few questions to
start off. I have no experience with PC104 whatsoever.
The goal is for a PC104 module to talk to another board with an FPGA on
it. Questions are:
1. Can I use any version of Linux on the PC104 ?
2. To save time, I hope t...PC104 Networking
Robert - 2004-04-14 03:44:00
I have a PC104 with Lan, what I would like to do is connect it up with a
desktop computer and comunicate between the PC and the PC104 through lan,
using dos and windows 98.
What programs are out there where I can have Dos talking to windows 98.
I just want control over the PC104 from the de...installing a new Disk on chip 2000 on pc104
vprasad007 - 2005-08-03 07:33:00
I am having problems installing a new M-systems disk on chip 200 (64Mb) o
the PC104). My PC104 is to run linux and i basically need to load an imag
onto the new disk on chip. I have a hard-drive connected to the pc104(usin
the old PPM-TX processor board) since the image is loaded on the harddrive...PC104 question
2004-08-31 17:26:00
Hi,
I am a PC104 newbie.
I am trying to boot a PC104 using a Compactflash flash memory card. To do
so, I first copied system files onto it (from a Windows98 machine). I then
used the flash card to boot the PC104, but encountered "Disk I/O error".
Could someone let me know what could be wrong?
...100 Ampro i386sx PC104 Single Board Computers With I/O boards. $60 For the SBC - I/O Combo.
Tough Guy - 2006-08-26 02:19:00
Hi,
I have 100 of the pc104 i386 pc104 sbc's. You have probably seen them
on here before. I was asking way to much. Please feel free to make an
offer. I am looking to sell all in one shot. I now have documentation
and drivers.
thanks,
Bob
...PC 104 Ethernet
Seven Days - 2004-04-04 06:52:00
Hi
Just recently purchased A PC104 board with ethernet lan,
Is there any software around or aplications where I can load the software
onto a 16mb disk on chip, I know that Iam using limited memory, but I have
read and seen at exibitions where they have pc104 boards connected to a
desktop with...Pc104 interfacing
Max - 2004-03-24 09:58:00
Hi all,
I use a CPLD to generate interrupt in a PC104 system. It work's fine.
The question is:
is correct connect CPLD output diretly to PC104 IRQ input (i don't need
interrupt sharing)? Or i need other hardware (pull-up resistor or other) ?
Thank's in advance
Max
...Choosing a PC104
Guy Macon - 2004-11-26 23:35:00
I have a project that I will be doing on a PC104 system.
Before I call the dozens of vendors who don't give pricing
info online, I would like to ask whether anyone else has
selected PC104 systems lately, and if so what they found.
REQUIREMENTS:
Very low performance 386 or 486. A 16Mhz ...PC104 Computers with enough room for 5 cards
2006-01-19 05:12:00
I have searched a lot for a computer or at least a box with a back
plane, where I can put in 5 or more PC104 cards.
All PC104 computers I saw, only had cages with room for 2-3 cards.
I think there must be providers offering larger cages.
Is there someone who provides large cages with a back...i am new to pc104 --- Help
adi - 2004-02-18 05:38:00
is there any one who manufacture pc104 with pentium 4 and firewire , Pci slot.
if so can you refer me to his web page? or correct me if i am wrong.
thanks alot
anahmany
...Re: SBC with USB Host Capabilities
2005-05-25 11:26:00
On 24 May, in article
bushxnyc@gmail.com wrote:
> Are their any in expensive SBC's with USBhost capability, preferably a
> 2 host board that can also handle and LCD device.
Just been looking round at PC104 and PC104+ myself, and come across
many! For starters:-
...PC104-687VL getting obsolete
Nivve - 2006-08-09 09:00:00
Hi,
we have been using the Nagasaki PC104-687 CPU module for long time
(also marketed as Taylor Randall, maybe others). Now they are obsolete
and I need to find some 5-10 boards. Anyone that can help me?
...PC104 + WIN 2003 Server + RAS + GPRS Modem: absurd ?
Generic Usenet Account - 2004-07-28 06:49:00
My idea is the following, is it completely absurd ?
I know that W2000 server works with RAS on a pc104.
Will W2003 server also work ?
I'm thinking about Win 2003 because i need the RAS (Remote Access Server for
TCP/IP)
- PC104 (CPU 400 Mhz + 128 MB ram)
- HD 30 GB
- GPRS radio modem t...ADC + FIFO --> IRQ on ISA (or PCI) --> Data Transfer
k - 2004-03-25 08:14:00
I'm also trying to design a PC104 (ISA) bus board.
I will interface an ADC (AD9220 or faster) via FIFO buffer to PC104 (ISA)
bus.
I need to control ADC to digitize input signal in a burst and store the
converted data into a FIFO.
When FIFO is full, I need to generate an interrupt to signal th...NVRAM module in PC104 format ?
Rick Merrill - 2004-04-28 08:16:00
I want 128bytes (small enough!) of NVRAM in
a PC104 format. Google has not done it so far!
Thanks for any leads. - RM
...PC 104 Embedded Software
Chris Atkins - 2004-08-28 08:29:00
What embedded software is out there to run on a PC104 for just data
collecting through the serial port.
For example, data from a electronic balance, with a RS 232 interface.
The PC104 has a 200mhz CPU 16mb of ram, 500 cf card as hard drive.
Thanks Chris
...Re: Looking for a low cost solution
Miki - 2005-03-10 02:40:00
Hello Joerg,
> > 1. Small display (8cmX13cm). Does not need to be high speed - it'll
> > show only pictures. Also there is no need for user feedback (touch
screen).
> 8cm by 13cm isn't small. How much interaction will there be between
MCU
> and screen controller?
Not much. My guess is...PC104 ISA bus.
LC - 2008-02-26 11:26:00
Hi,
I have a PC104 from kontron (mops_lcd) that
I can't read IO ports from the ISA bus,
The write to ports is ok but the read gets
0xff always. (even with datalines forced '0' all the time)
Looks that IO input is comming from elsewhere
as onboard devices like LPT or COM work well
I suspect ...PC104 CPU and Plugin boards for sale !
2006-06-08 09:13:00
I have some surplus PC104 boards from both Arcom and Advantech that are
for sale. I have the main boards and also various relay and mult-io
boards.
Please contact me if you wish to purchase the boards or have any
questions...
Peter
...PCI bus extension
Mouarf - 2005-02-16 11:53:00
hi,
is there a way to increase the number of PCI boards connected to a PC104+
motherboard to more than 4?
Are "PCI bridge" known to do this job or not?
Are there any PCI-PCI bridge board in PC104+ format?
Are there some low power 3.3V PCI bridge chip?
Are PCI bridge transparent to t...USB slave on a PC
Jason Curl - 2004-10-26 14:13:00
Hello,
I have a small PC104 device with one USB port. As of yet, I'm not too
familiar with USB, except to know there is exactly 1 master and many slaves.
I would like to know if it is possible to make the PC104 device look
like a slave, so that I can have it emulate a "usb storage device"....PC104 Embedded software
Simon Colins - 2004-09-14 11:12:00
I recently purchased a PC104, what operating systems can be purchased to run
these boards.
I have a Compact Flash Card aa a hard drive using windows 95 and 98 which
writes continusly to the compact flash.
I would imagine this would shorten the life of the card.
Would I be best using "CE" or...looking for an embedded solution
2005-07-08 09:24:00
i hope this is not OT.
I need to port an application for pocket pc on a single board computer.
The huge problem is gprs connectivity, on the pda(eten p300 gsm/gprs) i
can easily connect using pocket pc API.
How can i reach this on a sbc?
Is there a ready to use solution, with integrated gprs(wi...PC104 GPS
Clay Millar - 2004-09-10 10:28:00
For prospecting, I use a GPS connected to a PC104 through the serial port
for reading the data.
At the moment Iam just using windows 95.
Is there any other operating systems around and software that can read the
data from a GPS or other scientific instruments that plugs into the serial
port a...PC104 addressgin
MikeD - 2005-02-16 16:00:00
using PC104 with 16bit configuration. What size is an address? IE. if
i write 0xABCD to address 0x1234, did I infact write AB to 0x1234 and
CD to 0x1235?
I think this is how ISA handles IO writes, but im not sure. So when I
write 16 bits to an odd address I actualy get 2 writes to teh bus?
...Which RTOS?
Nemisis_2001 - 2006-03-10 16:36:00
Hi folks,
I am about to emabark on a new development using a COTS PC104 single
board computer (probably Arcom Viper) for use in an industrial control
system. The PC104 will perform the role of an autonomous serial data
acquisition hub with some basic control functions. The PC104 will be
insta...AmPro PC104 i386 SX Single Board Computer With I/O Boards FOR SALE
Tough Guy - 2006-07-14 03:25:00
Hi,
I have a buch of AmPro PC104 i386 SX Single Board Computer With I/O
Boards and I am looking for a perspective buyer. Contact me for more
info and pics of the SBC's.
thanks,
Bob
...100 ampro A13137 i386sx PC104 Single Board Computers with I/O boards $40 ea.
Tough Guy - 2006-08-31 00:40:00
Hi all,
I have about 100 i386 PC104 Single board computers and I am looking for
someone to take them all of my hands. I have a manual for the Ampro
A13137 Sbc and also the drivers for the I/O board and SBC. I am selling
each SBC / IO board set for $40.
thanks
...elimination of intercharacter gap in RS232 stream?
Bo - 2007-10-10 12:50:00
Writing an Embbeded Linux app for a PC104/Versalogic board. Linux 2.6.14.17.
Using write() to transmit data packets to another PC104 board. If I write()
30 bytes, sometimes there is a 2-5mS gap in the middle of the
transmission, usually at about byte 15-20, but sometimes at byte 29--as seen
o...High speed ADC board (12-16Bits, 10MHz,1-2In,4-16K FIFO,USB-PCI PC104+, Linux support)
2004-07-09 08:41:00
Can someone recomment an off the shelf product with the following specs;
Resolution : 12-16 bit
Conversion speed : 10Mega samples per second
Input Channel : 1-2
On board FIFO buffer : 4-16 K samples
Host Interface : USB or PCI interface to PC104+
SW support : Linux ...Re: PC/104 breadboard cards?
Chris Burrows - 2009-05-25 23:21:00
"larwe" wrote in message
news:f30ac933-353a-49fd-8e13-18ac992ae813@z5g2000vba.googlegroups.com...
>
> Failing that I'd be happy if I could just source the connector. That I
> haven't been able to find anywhere, though I assume it is there buried
> in Digi-Key's unfathomable search engin...100 AmPro PC104 i386 SX Single Board Computers With I/O Boards FOR SALE
Tough Guy - 2006-07-21 18:35:00
Hi all,
I have about 100 of these AmPro PC104 i386 SX Single Board Computers
With I/O Boards that are brand new. Contact me for Pics.
thanks,
Bob
...Looking for embedded Module with a VGA port
Thomas Reinzer - 2005-04-09 14:47:00
Hello,
I am looking to buy an embedded microcontroller board with the following
features:
1) Small (something like PC104 or smaller)
2) Direct connection for VGA monitors with graphic mode of at least
640x480 pixel, with at least 16, preferably 256 colors.
3) CPU power needed ist somethi...10MHz 12-16Bit ADC with 4K sample FIFO on PC104+ form factor
ADC - 2004-04-20 08:51:00
Would anybody point an ADC board with the following (or similar) specs?
Input Channels : 1 (or 2 with simultaneous sample&hold)
Conversion Speed : 10 MHz
Resolutions : 12-16 bits
Buffer : 4 K sample (or more) FIFO
Form Factor : PC104...PC104 platform conviniens for realtime application
Pavel - 2006-07-12 07:58:00
Hi all,
we have existing system based on signlechip microcomputer with RISC
procesor on 20 MHz , the system collect data from CAN bus and I/O cards
and each 20 ms execute several algorithms.
Our team prepare new architecture of this system based on PC104
architecture with procesor AMD Geode LX8...PC 104 questions for newbie
leutholl - 2006-03-21 18:56:00
Hi,
I'm new here ad new to PC 104.
I have a PC104 system in front of me having:
- RS232 port
- MVB/CAN Bus interface
- Parallel port
- PS/2 keyboard port
- special connector to a touchscreen which i have (working!)
- some little rotary switch to dial in a address for something in
hexadeci...Re: Windows XPe/Modem with PPP does not detect lost connection
dalai lamah - 2006-11-26 06:27:00
Un bel giorno Christian Walter digitò:
> I tried the same setup on a normal PC with the same modem but different
> serial ports and there everything works correctly. This lead me to
> conclude that there might be something wrong with the serial drivers not
> notifying the application tha...Terrible noise from audio output of my pc104.
MGM Systems - 2006-10-06 03:31:00
I purchase two PC104. The first with VIA Eden 600 and the second with Intel
Celeron 400.
You can see specs at http://www.seco.it/old/schede_prod/M585-HTE01A.htm.
I installed XP. This cards don't have headphone output but only speaker
output (4 pins L+,L-,R+,R-). I've tryed to connect a headp...Re: PC-104 vs EBX
Robert Lacoste - 2004-04-16 05:54:00
"DD" a écrit dans le message de
news:RTKfc.51886$8L1.80@newssvr25.news.prodigy.com...
> I am trying to decide between PC-104 and EBX. I don't need the small size
> of PC-104, but I heard that the construction is more rugged, which is good
> for machine's my rough & tough environment. I...