Sign in
Search rabbit-semi
Subscribe to rabbit-semi
Ads
Discussion Groups
See Also
Discussion Groups | Rabbit-Semi | Domotic
This is a group for folks designing and programming embedded systems using the Rabbit Semiconductor C-programmable microcontroller. Rabbit Semi is a spin-off from Z-World who makes a variety of embedded modules and tools. This group is not affiliated with either Rabbit or Z-World, but is a user forum for sharing ideas, asking questions, flaunting knowledge, and other typical user group stuff. The Rabbit is a powerful uC, supported by a full-featured C-compiler.
Domotic - Saray Gonzalez Suarez - Oct 9 9:54:44 2009
Hello,
I want to realise a domótica installation to control and supervision a heating system. Its possible with rabbit elements?
Thank you.
------------------------------------------------------------------------
Saray González
Fundación CTIC
Departamento I+D+i
E-mail: s...@fundacionctic.org Tfno. +34 984 29 12 12
Parque Científico Tecnológico Gijón-Asturias-Spain www.fundacionctic.org
------------------------------------------------------------------------
(You need to be a member of rabbit-semi -- send a blank email to rabbit-semi-subscribe@yahoogroups.com )
I want to realise a domótica installation to control and supervision a heating system. Its possible with rabbit elements?
Thank you.
------------------------------------------------------------------------
Saray González
Fundación CTIC
Departamento I+D+i
E-mail: s...@fundacionctic.org Tfno. +34 984 29 12 12
Parque Científico Tecnológico Gijón-Asturias-Spain www.fundacionctic.org
------------------------------------------------------------------------
(You need to be a member of rabbit-semi -- send a blank email to rabbit-semi-subscribe@yahoogroups.com )
Re: Domotic - eilidhs_daddy - Oct 9 10:25:51 2009
The simple answer is 'of course it is possible'.
Rabbit produce a range of products from processor chips and IO Chips, throu=
gh core modules and mini modules, to single board computers.
They have various combinations of I/O, including parallel ports, serial por=
ts (RS232 and RS485), Analog inputs and digital I/O.
They are all fully programmable, so they can do anything really.
It's up to you as the system designer to set out the requirments, produce a=
spec, develope the product and test it.
To begin with you need to know the requirements. What type of signals do yo=
u need to control a dom=F3tica system? RS485? Digital? Analog for temperatu=
re sensors?=20
-K
--- In r...@yahoogroups.com, "Saray Gonzalez Suarez"
>
> Hello,
> I want to realise a dom=F3tica installation to control and supervision a=
heating system. Its possible with rabbit elements?
> Thank you.
>=20
> ------------------------------------------------------------------------
> Saray Gonz=E1lez
> Fundaci=F3n CTIC
> Departamento I+D+i
> E-mail: saray.gonzalez@... Tfno. +34 984 29 12 12=20
> Parque Cient=EDfico Tecnol=F3gico Gij=F3n-Asturias-Spain www.fundacioncti=
c.org=20
> ------------------------------------------------------------------------
>
------------------------------------
(You need to be a member of rabbit-semi -- send a blank email to rabbit-semi-subscribe@yahoogroups.com )
RE: Re: Domotic - Saray Gonzalez Suarez - Oct 9 13:12:51 2009
Hello,
Thank you for your answer.
Is too soon, in this moment, is a first idea, but I will work with analog inputs, digital inputs and digital outputs. I need a tactil screen for supervision and control too. A small "SCADA".
Sorry for my english.
Thank you.
-----Mensaje original-----
De: r...@yahoogroups.com en nombre de eilidhs_daddy
Enviado el: vie 09/10/2009 16:25
Para: r...@yahoogroups.com
Asunto: [rabbit-semi] Re: Domotic
The simple answer is 'of course it is possible'.
Rabbit produce a range of products from processor chips and IO Chips, through core modules and mini modules, to single board computers.
They have various combinations of I/O, including parallel ports, serial ports (RS232 and RS485), Analog inputs and digital I/O.
They are all fully programmable, so they can do anything really.
It's up to you as the system designer to set out the requirments, produce a spec, develope the product and test it.
To begin with you need to know the requirements. What type of signals do you need to control a domótica system? RS485? Digital? Analog for temperature sensors?
-K
--- In r...@yahoogroups.com, "Saray Gonzalez Suarez"
>
> Hello,
> I want to realise a domótica installation to control and supervision a heating system. Its possible with rabbit elements?
> Thank you.
>
> ------------------------------------------------------------------------
> Saray González
> Fundación CTIC
> Departamento I+D+i
> E-mail: saray.gonzalez@... Tfno. +34 984 29 12 12
> Parque Científico Tecnológico Gijón-Asturias-Spain www.fundacionctic.org
> ------------------------------------------------------------------------
>
------------------------------------
(You need to be a member of rabbit-semi -- send a blank email to rabbit-semi-subscribe@yahoogroups.com )
Re: Domotic - eilidhs_daddy - Oct 9 17:27:21 2009
Something like the Rabbit OP7200 might be good for you, it has a touch-scre=
en, loads of analog inputs, digital inputs and outputs, ethernet and RS485 =
all on board.
-Kenny
--- In r...@yahoogroups.com, "Saray Gonzalez Suarez"
>
>=20
> Hello,
> Thank you for your answer.
> Is too soon, in this moment, is a first idea, but I will work with analog=
inputs, digital inputs and digital outputs. I need a tactil screen for sup=
ervision and control too. A small "SCADA".
> Sorry for my english.
> Thank you.=20
>=20
> -----Mensaje original-----
> De: r...@yahoogroups.com en nombre de eilidhs_daddy
> Enviado el: vie 09/10/2009 16:25
> Para: r...@yahoogroups.com
> Asunto: [rabbit-semi] Re: Domotic
>=20=20
>=20
> The simple answer is 'of course it is possible'.
>=20
> Rabbit produce a range of products from processor chips and IO Chips, thr=
ough core modules and mini modules, to single board computers.
>=20
> They have various combinations of I/O, including parallel ports, serial p=
orts (RS232 and RS485), Analog inputs and digital I/O.
>=20
> They are all fully programmable, so they can do anything really.
>=20
> It's up to you as the system designer to set out the requirments, produce=
a spec, develope the product and test it.
>=20
> To begin with you need to know the requirements. What type of signals do =
you need to control a dom=F3tica system? RS485? Digital? Analog for tempera=
ture sensors?=20
>=20
> -K
>=20
> --- In r...@yahoogroups.com, "Saray Gonzalez Suarez"
> >
> > Hello,
> > I want to realise a dom=F3tica installation to control and supervision=
a heating system. Its possible with rabbit elements?
> > Thank you.
> >=20
> > -----------------------------------------------------------------------=
-
> > Saray Gonz=E1lez
> > Fundaci=F3n CTIC
> > Departamento I+D+i
> > E-mail: saray.gonzalez@ Tfno. +34 984 29 12 12=20
> > Parque Cient=EDfico Tecnol=F3gico Gij=F3n-Asturias-Spain www.fundacionc=
tic.org=20
> > -----------------------------------------------------------------------=
-
>
------------------------------------
______________________________
controlSUITE™ software. Comprehensive. Intuitive. Optimized.
Real-world software for real-time control. Details Here!
(You need to be a member of rabbit-semi -- send a blank email to rabbit-semi-subscribe@yahoogroups.com )
en, loads of analog inputs, digital inputs and outputs, ethernet and RS485 =
all on board.
-Kenny
--- In r...@yahoogroups.com, "Saray Gonzalez Suarez"
>
>=20
> Hello,
> Thank you for your answer.
> Is too soon, in this moment, is a first idea, but I will work with analog=
inputs, digital inputs and digital outputs. I need a tactil screen for sup=
ervision and control too. A small "SCADA".
> Sorry for my english.
> Thank you.=20
>=20
> -----Mensaje original-----
> De: r...@yahoogroups.com en nombre de eilidhs_daddy
> Enviado el: vie 09/10/2009 16:25
> Para: r...@yahoogroups.com
> Asunto: [rabbit-semi] Re: Domotic
>=20=20
>=20
> The simple answer is 'of course it is possible'.
>=20
> Rabbit produce a range of products from processor chips and IO Chips, thr=
ough core modules and mini modules, to single board computers.
>=20
> They have various combinations of I/O, including parallel ports, serial p=
orts (RS232 and RS485), Analog inputs and digital I/O.
>=20
> They are all fully programmable, so they can do anything really.
>=20
> It's up to you as the system designer to set out the requirments, produce=
a spec, develope the product and test it.
>=20
> To begin with you need to know the requirements. What type of signals do =
you need to control a dom=F3tica system? RS485? Digital? Analog for tempera=
ture sensors?=20
>=20
> -K
>=20
> --- In r...@yahoogroups.com, "Saray Gonzalez Suarez"
> >
> > Hello,
> > I want to realise a dom=F3tica installation to control and supervision=
a heating system. Its possible with rabbit elements?
> > Thank you.
> >=20
> > -----------------------------------------------------------------------=
-
> > Saray Gonz=E1lez
> > Fundaci=F3n CTIC
> > Departamento I+D+i
> > E-mail: saray.gonzalez@ Tfno. +34 984 29 12 12=20
> > Parque Cient=EDfico Tecnol=F3gico Gij=F3n-Asturias-Spain www.fundacionc=
tic.org=20
> > -----------------------------------------------------------------------=
-
>
------------------------------------
______________________________
controlSUITE™ software. Comprehensive. Intuitive. Optimized.
Real-world software for real-time control. Details Here!
(You need to be a member of rabbit-semi -- send a blank email to rabbit-semi-subscribe@yahoogroups.com )
RE: Re: Domotic - Saray Gonzalez Suarez - Oct 10 13:54:39 2009
Hello,
Thank you for your help Kenny.
I will look for information about OP7200.
Thank you.
-----Mensaje original-----
De: r...@yahoogroups.com en nombre de eilidhs_daddy
Enviado el: vie 09/10/2009 23:25
Para: r...@yahoogroups.com
Asunto: [rabbit-semi] Re: Domotic
Something like the Rabbit OP7200 might be good for you, it has a touch-screen, loads of analog inputs, digital inputs and outputs, ethernet and RS485 all on board.
-Kenny
--- In r...@yahoogroups.com, "Saray Gonzalez Suarez"
> Hello,
> Thank you for your answer.
> Is too soon, in this moment, is a first idea, but I will work with analog inputs, digital inputs and digital outputs. I need a tactil screen for supervision and control too. A small "SCADA".
> Sorry for my english.
> Thank you.
>
> -----Mensaje original-----
> De: r...@yahoogroups.com en nombre de eilidhs_daddy
> Enviado el: vie 09/10/2009 16:25
> Para: r...@yahoogroups.com
> Asunto: [rabbit-semi] Re: Domotic
>
>
> The simple answer is 'of course it is possible'.
>
> Rabbit produce a range of products from processor chips and IO Chips, through core modules and mini modules, to single board computers.
>
> They have various combinations of I/O, including parallel ports, serial ports (RS232 and RS485), Analog inputs and digital I/O.
>
> They are all fully programmable, so they can do anything really.
>
> It's up to you as the system designer to set out the requirments, produce a spec, develope the product and test it.
>
> To begin with you need to know the requirements. What type of signals do you need to control a domótica system? RS485? Digital? Analog for temperature sensors?
>
> -K
>
> --- In r...@yahoogroups.com, "Saray Gonzalez Suarez"
> >
> > Hello,
> > I want to realise a domótica installation to control and supervision a heating system. Its possible with rabbit elements?
> > Thank you.
> >
> > ------------------------------------------------------------------------
> > Saray González
> > Fundación CTIC
> > Departamento I+D+i
> > E-mail: saray.gonzalez@ Tfno. +34 984 29 12 12
> > Parque Científico Tecnológico Gijón-Asturias-Spain www.fundacionctic.org
> > ------------------------------------------------------------------------
>
------------------------------------
(You need to be a member of rabbit-semi -- send a blank email to rabbit-semi-subscribe@yahoogroups.com )
RE: Re: Domotic - Saray Gonzalez Suarez - Oct 11 8:33:32 2009
Hello,
I need to Know if it's posible the following configuration with rabbit elements:
a web SCADA for domotic supervision and domotic control.
I need realise control and supervision from a touchscreen and the panels must be web and they must allow remote access.Is this posible with OP7200?What options do i have?
Sorry I have not much knowledge on these issues.
Thank you.
________________________________
De: r...@yahoogroups.com en nombre de eilidhs_daddy
Enviado el: vie 09/10/2009 23:25
Para: r...@yahoogroups.com
Asunto: [rabbit-semi] Re: Domotic
Something like the Rabbit OP7200 might be good for you, it has a touch-screen, loads of analog inputs, digital inputs and outputs, ethernet and RS485 all on board.
-Kenny
--- In r...@yahoogroups.com , "Saray Gonzalez
Suarez" wrote:
> Hello,
> Thank you for your answer.
> Is too soon, in this moment, is a first idea, but I will work with analog inputs, digital inputs and digital outputs. I need a tactil screen for supervision and control too. A small "SCADA".
> Sorry for my english.
> Thank you.
>
> -----Mensaje original-----
> De: r...@yahoogroups.com en nombre de
eilidhs_daddy
> Enviado el: vie 09/10/2009 16:25
> Para: r...@yahoogroups.com
> Asunto: [rabbit-semi] Re: Domotic
> The simple answer is 'of course it is possible'.
>
> Rabbit produce a range of products from processor chips and IO Chips, through core modules and mini modules, to single board computers.
>
> They have various combinations of I/O, including parallel ports, serial ports (RS232 and RS485), Analog inputs and digital I/O.
>
> They are all fully programmable, so they can do anything really.
>
> It's up to you as the system designer to set out the requirments, produce a spec, develope the product and test it.
>
> To begin with you need to know the requirements. What type of signals do you need to control a domótica system? RS485? Digital? Analog for temperature sensors?
>
> -K
>
> --- In r...@yahoogroups.com , "Saray Gonzalez
Suarez" wrote:
> >
> > Hello,
> > I want to realise a domótica installation to control and supervision a heating system. Its possible with rabbit elements?
> > Thank you.
> >
> > ----------------------------------------------------------
> > Saray González
> > Fundación CTIC
> > Departamento I+D+i
> > E-mail: saray.gonzalez@ Tfno. +34 984 29 12 12
> > Parque Científico Tecnológico Gijón-Asturias-Spain www.fundacionctic.org
> > ----------------------------------------------------------
>
------------------------------------
(You need to be a member of rabbit-semi -- send a blank email to rabbit-semi-subscribe@yahoogroups.com )
I need to Know if it's posible the following configuration with rabbit elements:
a web SCADA for domotic supervision and domotic control.
I need realise control and supervision from a touchscreen and the panels must be web and they must allow remote access.Is this posible with OP7200?What options do i have?
Sorry I have not much knowledge on these issues.
Thank you.
________________________________
De: r...@yahoogroups.com en nombre de eilidhs_daddy
Enviado el: vie 09/10/2009 23:25
Para: r...@yahoogroups.com
Asunto: [rabbit-semi] Re: Domotic
Something like the Rabbit OP7200 might be good for you, it has a touch-screen, loads of analog inputs, digital inputs and outputs, ethernet and RS485 all on board.
-Kenny
--- In r...@yahoogroups.com
> Hello,
> Thank you for your answer.
> Is too soon, in this moment, is a first idea, but I will work with analog inputs, digital inputs and digital outputs. I need a tactil screen for supervision and control too. A small "SCADA".
> Sorry for my english.
> Thank you.
>
> -----Mensaje original-----
> De: r...@yahoogroups.com
> Enviado el: vie 09/10/2009 16:25
> Para: r...@yahoogroups.com
> Asunto: [rabbit-semi] Re: Domotic
> The simple answer is 'of course it is possible'.
>
> Rabbit produce a range of products from processor chips and IO Chips, through core modules and mini modules, to single board computers.
>
> They have various combinations of I/O, including parallel ports, serial ports (RS232 and RS485), Analog inputs and digital I/O.
>
> They are all fully programmable, so they can do anything really.
>
> It's up to you as the system designer to set out the requirments, produce a spec, develope the product and test it.
>
> To begin with you need to know the requirements. What type of signals do you need to control a domótica system? RS485? Digital? Analog for temperature sensors?
>
> -K
>
> --- In r...@yahoogroups.com
> >
> > Hello,
> > I want to realise a domótica installation to control and supervision a heating system. Its possible with rabbit elements?
> > Thank you.
> >
> > ----------------------------------------------------------
> > Saray González
> > Fundación CTIC
> > Departamento I+D+i
> > E-mail: saray.gonzalez@ Tfno. +34 984 29 12 12
> > Parque Científico Tecnológico Gijón-Asturias-Spain www.fundacionctic.org
> > ----------------------------------------------------------
>
------------------------------------
(You need to be a member of rabbit-semi -- send a blank email to rabbit-semi-subscribe@yahoogroups.com )
RE: Re: Domotic - "Moore, Robert" - Oct 11 10:23:26 2009
Hi
I think you need to look at all the systems you wish to control and how a remote controller can talk to each of them. That will form the basic outline of the SCADA system you need.
You mention control and supervision of a heating system. The domotics idea usually is much more extensive than that. What is your goal and what cannot be achieved with one of the PID controllers from Honeywell.
regards
bob moore
________________________________
From: r...@yahoogroups.com on behalf of Saray Gonzalez Suarez
Sent: Sun 10/11/2009 8:33 AM
To: r...@yahoogroups.com
Subject: RE: [rabbit-semi] Re: Domotic
Hello,
I need to Know if it's posible the following configuration with rabbit elements:
a web SCADA for domotic supervision and domotic control.
I need realise control and supervision from a touchscreen and the panels must be web and they must allow remote access.Is this posible with OP7200?What options do i have?
Sorry I have not much knowledge on these issues.
Thank you.
________________________________
De: r...@yahoogroups.com en nombre de eilidhs_daddy
Enviado el: vie 09/10/2009 23:25
Para: r...@yahoogroups.com
Asunto: [rabbit-semi] Re: Domotic
Something like the Rabbit OP7200 might be good for you, it has a touch-screen, loads of analog inputs, digital inputs and outputs, ethernet and RS485 all on board.
-Kenny
--- In r...@yahoogroups.com , "Saray Gonzalez
Suarez" wrote:
> Hello,
> Thank you for your answer.
> Is too soon, in this moment, is a first idea, but I will work with analog inputs, digital inputs and digital outputs. I need a tactil screen for supervision and control too. A small "SCADA".
> Sorry for my english.
> Thank you.
>
> -----Mensaje original-----
> De: r...@yahoogroups.com en nombre de
eilidhs_daddy
> Enviado el: vie 09/10/2009 16:25
> Para: r...@yahoogroups.com
> Asunto: [rabbit-semi] Re: Domotic
> The simple answer is 'of course it is possible'.
>
> Rabbit produce a range of products from processor chips and IO Chips, through core modules and mini modules, to single board computers.
>
> They have various combinations of I/O, including parallel ports, serial ports (RS232 and RS485), Analog inputs and digital I/O.
>
> They are all fully programmable, so they can do anything really.
>
> It's up to you as the system designer to set out the requirments, produce a spec, develope the product and test it.
>
> To begin with you need to know the requirements. What type of signals do you need to control a domótica system? RS485? Digital? Analog for temperature sensors?
>
> -K
>
> --- In r...@yahoogroups.com , "Saray Gonzalez
Suarez" wrote:
> >
> > Hello,
> > I want to realise a domótica installation to control and supervision a heating system. Its possible with rabbit elements?
> > Thank you.
> >
> > ----------------------------------------------------------
> > Saray González
> > Fundación CTIC
> > Departamento I+D+i
> > E-mail: saray.gonzalez@ Tfno. +34 984 29 12 12
> > Parque Científico Tecnológico Gijón-Asturias-Spain www.fundacionctic.org
> > ----------------------------------------------------------
>
------------------------------------
(You need to be a member of rabbit-semi -- send a blank email to rabbit-semi-subscribe@yahoogroups.com )
I think you need to look at all the systems you wish to control and how a remote controller can talk to each of them. That will form the basic outline of the SCADA system you need.
You mention control and supervision of a heating system. The domotics idea usually is much more extensive than that. What is your goal and what cannot be achieved with one of the PID controllers from Honeywell.
regards
bob moore
________________________________
From: r...@yahoogroups.com on behalf of Saray Gonzalez Suarez
Sent: Sun 10/11/2009 8:33 AM
To: r...@yahoogroups.com
Subject: RE: [rabbit-semi] Re: Domotic
Hello,
I need to Know if it's posible the following configuration with rabbit elements:
a web SCADA for domotic supervision and domotic control.
I need realise control and supervision from a touchscreen and the panels must be web and they must allow remote access.Is this posible with OP7200?What options do i have?
Sorry I have not much knowledge on these issues.
Thank you.
________________________________
De: r...@yahoogroups.com en nombre de eilidhs_daddy
Enviado el: vie 09/10/2009 23:25
Para: r...@yahoogroups.com
Asunto: [rabbit-semi] Re: Domotic
Something like the Rabbit OP7200 might be good for you, it has a touch-screen, loads of analog inputs, digital inputs and outputs, ethernet and RS485 all on board.
-Kenny
--- In r...@yahoogroups.com
> Hello,
> Thank you for your answer.
> Is too soon, in this moment, is a first idea, but I will work with analog inputs, digital inputs and digital outputs. I need a tactil screen for supervision and control too. A small "SCADA".
> Sorry for my english.
> Thank you.
>
> -----Mensaje original-----
> De: r...@yahoogroups.com
> Enviado el: vie 09/10/2009 16:25
> Para: r...@yahoogroups.com
> Asunto: [rabbit-semi] Re: Domotic
> The simple answer is 'of course it is possible'.
>
> Rabbit produce a range of products from processor chips and IO Chips, through core modules and mini modules, to single board computers.
>
> They have various combinations of I/O, including parallel ports, serial ports (RS232 and RS485), Analog inputs and digital I/O.
>
> They are all fully programmable, so they can do anything really.
>
> It's up to you as the system designer to set out the requirments, produce a spec, develope the product and test it.
>
> To begin with you need to know the requirements. What type of signals do you need to control a domótica system? RS485? Digital? Analog for temperature sensors?
>
> -K
>
> --- In r...@yahoogroups.com
> >
> > Hello,
> > I want to realise a domótica installation to control and supervision a heating system. Its possible with rabbit elements?
> > Thank you.
> >
> > ----------------------------------------------------------
> > Saray González
> > Fundación CTIC
> > Departamento I+D+i
> > E-mail: saray.gonzalez@ Tfno. +34 984 29 12 12
> > Parque Científico Tecnológico Gijón-Asturias-Spain www.fundacionctic.org
> > ----------------------------------------------------------
>
------------------------------------
(You need to be a member of rabbit-semi -- send a blank email to rabbit-semi-subscribe@yahoogroups.com )
RE: Re: Domotic - Saray Gonzalez Suarez - Oct 11 15:37:43 2009
Hello,
I'm looking for different posibilities of various manufacturers. I just need to know if, with this conditions (a web SCADA for domotic supervision and domotic control and control and supervision from a touchscreen and the panels must be web and they must allow remote access) it's possible to use Rabbit products. Then,final instalation will depend on the sensors, the comunication bus,......).
Thank you.
-----Mensaje original-----
De: r...@yahoogroups.com en nombre de Moore, Robert
Enviado el: dom 11/10/2009 16:22
Para: r...@yahoogroups.com
Asunto: RE: [rabbit-semi] Re: Domotic
Hi
I think you need to look at all the systems you wish to control and how a remote controller can talk to each of them. That will form the basic outline of the SCADA system you need.
You mention control and supervision of a heating system. The domotics idea usually is much more extensive than that. What is your goal and what cannot be achieved with one of the PID controllers from Honeywell.
regards
bob moore
_____
From: r...@yahoogroups.com on behalf of Saray Gonzalez Suarez
Sent: Sun 10/11/2009 8:33 AM
To: r...@yahoogroups.com
Subject: RE: [rabbit-semi] Re: Domotic
Hello,
I need to Know if it's posible the following configuration with rabbit elements:
a web SCADA for domotic supervision and domotic control.
I need realise control and supervision from a touchscreen and the panels must be web and they must allow remote access.Is this posible with OP7200?What options do i have?
Sorry I have not much knowledge on these issues.
Thank you.
_____
De: r...@yahoogroups.com en nombre de eilidhs_daddy
Enviado el: vie 09/10/2009 23:25
Para: r...@yahoogroups.com
Asunto: [rabbit-semi] Re: Domotic
Something like the Rabbit OP7200 might be good for you, it has a touch-screen, loads of analog inputs, digital inputs and outputs, ethernet and RS485 all on board.
-Kenny
--- In rabbit-semi@
> Hello,
> Thank you for your answer.
> Is too soon, in this moment, is a first idea, but I will work with analog inputs, digital inputs and digital outputs. I need a tactil screen for supervision and control too. A small "SCADA".
> Sorry for my english.
> Thank you.
>
> -----Mensaje original-----
> De: rabbit-semi@
> Enviado el: vie 09/10/2009 16:25
> Para: rabbit-semi@
> Asunto: [rabbit-semi] Re: Domotic
> The simple answer is 'of course it is possible'.
>
> Rabbit produce a range of products from processor chips and IO Chips, through core modules and mini modules, to single board computers.
>
> They have various combinations of I/O, including parallel ports, serial ports (RS232 and RS485), Analog inputs and digital I/O.
>
> They are all fully programmable, so they can do anything really.
>
> It's up to you as the system designer to set out the requirments, produce a spec, develope the product and test it.
>
> To begin with you need to know the requirements. What type of signals do you need to control a domótica system? RS485? Digital? Analog for temperature sensors?
>
> -K
>
> --- In rabbit-semi@
> >
> > Hello,
> > I want to realise a domótica installation to control and supervision a heating system. Its possible with rabbit elements?
> > Thank you.
> >
> > ----------------------------------------------------------
> > Saray González
> > Fundación CTIC
> > Departamento I+D+i
> > E-mail: saray.gonzalez@ Tfno. +34 984 29 12 12
> > Parque Científico Tecnológico Gijón-Asturias-Spain www.fundacionctic.org
> > ----------------------------------------------------------
>
------------------------------------
(You need to be a member of rabbit-semi -- send a blank email to rabbit-semi-subscribe@yahoogroups.com )