I bought a OOPic ver B.1.0 a few years back and had no trouble using
it for a while. I had to shelf it for a few years and now that I am
trying to use it again I am having troubles configuring the OOPic IDE
to use a parallel port to program it. I am able to manually set the
port to 378 Hex and do a "find delay" ok. But when I try to do "find
parallel cable" or save the manual settings I get an error box saying
"Internal Error in PortInp of I2CFuncs." I have googled the error
message and also searched this group and could not find any answers.

I am using WinXP and have made sure the port is turned on in the BIOS.
I have also removed and reinstalled the LPT port in WinXP settings.
I also tried using OOPic IDE v5 and V6. IDE v5 will just crash with
no error box when I try to setup the parallel port.

Thanks for any help.

Jason
------------------------------------



(You need to be a member of oopic -- send a blank email to oopic-subscribe@yahoogroups.com )

--- In o...@yahoogroups.com, "zang206" wrote:
>
> I bought a OOPic ver B.1.0 a few years back and had no trouble using
> it for a while. I had to shelf it for a few years and now that I am
> trying to use it again I am having troubles configuring the OOPic IDE
> to use a parallel port to program it. I am able to manually set the
> port to 378 Hex and do a "find delay" ok. But when I try to do "find
> parallel cable" or save the manual settings I get an error box saying
> "Internal Error in PortInp of I2CFuncs." I have googled the error
> message and also searched this group and could not find any answers.
>
> I am using WinXP and have made sure the port is turned on in the BIOS.
> I have also removed and reinstalled the LPT port in WinXP settings.
> I also tried using OOPic IDE v5 and V6. IDE v5 will just crash with
> no error box when I try to setup the parallel port.
>
> Thanks for any help.
>
> Jason
>

Did you install Port95NT.exe as required? See www.oopic.com/dloadp.html

Richard

========================================================================
Groups related to oopic
========================================================================

SeattleRobotics (233 common members)
http://groups.yahoo.com/group/SeattleRobotics?v=1&t=ipt&ch=email&pub=groups&slk=aftr0&sec=recg
Mechanical/Robotics: The Seattle Robotics Society is a world wide group...

piclist (183 common members)
http://groups.yahoo.com/group/piclist?v=1&t=ipt&ch=email&pub=groups&slk=aftr1&sec=recg
Microprocessors/Microcontrollers: A discussion group for the PICMicro microcontrolle...

Robotics (130 common members)
http://groups.yahoo.com/group/Robotics?v=1&t=ipt&ch=email&pub=groups&slk=aftr2&sec=recg
Mechanical/Robotics: Robotics discussion group. This egroup is for thos...

rabbit-semi (119 common members)
http://groups.yahoo.com/group/rabbit-semi?v=1&t=ipt&ch=email&pub=groups&slk=aftr3&sec=recg
Microprocessors/Microcontrollers: This is a user group for folks designing and progr...

PARTS (107 common members)
http://groups.yahoo.com/group/PARTS?v=1&t=ipt&ch=email&pub=groups&slk=aftr4&sec=recg
Mechanical/Robotics: Portland Area Robotics Society is a club formed to...
------------------------------------



(You need to be a member of oopic -- send a blank email to oopic-subscribe@yahoogroups.com )

--- In o...@yahoogroups.com, "rtstofer" wrote:
>
> --- In o...@yahoogroups.com, "zang206" wrote:
> >
> > I bought a OOPic ver B.1.0 a few years back and had no trouble using
> > it for a while. I had to shelf it for a few years and now that I am
> > trying to use it again I am having troubles configuring the OOPic IDE
> > to use a parallel port to program it. I am able to manually set the
> > port to 378 Hex and do a "find delay" ok. But when I try to do "find
> > parallel cable" or save the manual settings I get an error box saying
> > "Internal Error in PortInp of I2CFuncs." I have googled the error
> > message and also searched this group and could not find any answers.
> >
> > I am using WinXP and have made sure the port is turned on in the BIOS.
> > I have also removed and reinstalled the LPT port in WinXP settings.
> > I also tried using OOPic IDE v5 and V6. IDE v5 will just crash with
> > no error box when I try to setup the parallel port.
> >
> > Thanks for any help.
> >
> > Jason
> > Did you install Port95NT.exe as required? See www.oopic.com/dloadp.html
>
> Richard
>

I overlooked that. For some reason I thought I didn't have to install
it on XP. Thanks for the help. It works perfect now.

Jason

------------------------------------



(You need to be a member of oopic -- send a blank email to oopic-subscribe@yahoogroups.com )