Hello, I m trying to program this micro XMS430F5438, using a parallel jtag =
interface and IAR V4.11B/W32 (4.11.2.9), but I get an error as the chip is =
not connected. From the micro side I only have the VCC, gnd and the pins fo=
r the Jtag, (TDO,TDI,TMS,TCK, TEST)=C2=A0the reset is pulled up

>From the jtag side I have one home made circuit=C2=A0 copied from TI. Where=
could be the problem?.Have I missed something important?=20
Thanks for your help.
Yahoo! Cocina
Recetas pr=C3=A1cticas y comida saludable
http://ar.mujer.yahoo.com/cocina/

[Non-text portions of this message have been removed]
------------------------------------



(You need to be a member of msp430 -- send a blank email to msp430-subscribe@yahoogroups.com )

In the IAR project options do you have the correct device selected. You
must select the XMS430F5438 and not the MSP430F5438.

I have been using the spy-bi-wire interface without any problems but have
not tried the full JTAG.

Ian

2008/9/18 mm bb

> Hello, I m trying to program this micro XMS430F5438, using a parallel jta=
g
> interface and IAR V4.11B/W32 (4.11.2.9), but I get an error as the chip i=
s
> not connected. From the micro side I only have the VCC, gnd and the pins =
for
> the Jtag, (TDO,TDI,TMS,TCK, TEST) the reset is pulled up
>
> From the jtag side I have one home made circuit copied from TI. Where
> could be the problem?.Have I missed something important?
> Thanks for your help.
> Yahoo! Cocina
> Recetas pr=E1cticas y comida saludable
> http://ar.mujer.yahoo.com/cocina/
>
> [Non-text portions of this message have been removed]
> ------------------------------------



(You need to be a member of msp430 -- send a blank email to msp430-subscribe@yahoogroups.com )

Hello!

I think it has nothing to do with choosing MSP instead of XMS. I have never=
tried,
but I heard recently at TI advanced conference that the parallel port emula=
tion
tool cannot be used with this device. I am afraid you will have to buy a US=
B
emulation tool...

Pascal.

--- In m...@yahoogroups.com, mm bb wrote:
>
> Hello, I m trying to program this micro XMS430F5438, using a parallel jta=
g interface and=20
IAR V4.11B/W32 (4.11.2.9), but I get an error as the chip is not connected.=
From the micro=20
side I only have the VCC, gnd and the pins for the Jtag, (TDO,TDI,TMS,TCK, =
TEST)=C2=A0the=20
reset is pulled up
>=20
> From the jtag side I have one home made circuit=C2=A0 copied from TI. Whe=
re could be the=20
problem?.Have I missed something important?=20
> Thanks for your help.
>=20
>=20
> Yahoo! Cocina
> Recetas pr=C3=A1cticas y comida saludable
> http://ar.mujer.yahoo.com/cocina/
>=20
> [Non-text portions of this message have been removed]
>

------------------------------------



(You need to be a member of msp430 -- send a blank email to msp430-subscribe@yahoogroups.com )

Hi,

According to my knowledge both MSP-FET430UIF, MSP-FET430PIF can be used as =
an interface.
But I haven't tried.

Did you go through 5xx documents.
The below document mentions that the JTAG pins are shared with general-purp=
ose I/O, which differs in most MSP430x2xx and MSP430x4xx.
page 4 in http://focus.ti.com/lit/an/slaa396/slaa396.pdf.

I don't know how much this could help you.

regards...
----- Original Message ----
From: p_murayama
To: m...@yahoogroups.com
Sent: Thursday, September 18, 2008 11:57:59 PM
Subject: [msp430] Re: msp430f5438
Hello!

I think it has nothing to do with choosing MSP instead of XMS. I have never=
tried,
but I heard recently at TI advanced conference that the parallel port emula=
tion
tool cannot be used with this device. I am afraid you will have to buy a US=
B
emulation tool...

Pascal.

--- In msp430@yahoogroups. com, mm bb wrote:
>
> Hello, I m trying to program this micro XMS430F5438, using a parallel jta=
g interface and=20
IAR V4.11B/W32 (4.11.2.9), but I get an error as the chip is not connected.=
From the micro=20
side I only have the VCC, gnd and the pins for the Jtag, (TDO,TDI,TMS, TCK,=
TEST)=C2=A0the=20
reset is pulled up
>=20
> From the jtag side I have one home made circuit=C2=A0 copied from TI. Whe=
re could be the=20
problem?.Have I missed something important?=20
> Thanks for your help.
>=20
>=20
> Yahoo! Cocina
> Recetas pr=C3=A1cticas y comida saludable
> http://ar.mujer. yahoo.com/ cocina/
>=20
> [Non-text portions of this message have been removed]
>

__._,_..___=20
Messages in this topic (3) Reply (via web post) | Start a new topic=20
Messages | Files | Photos | Links | Database | Polls | Members | Calendar=20

=20
Change settings via the Web (Yahoo! ID required)=20
Change settings via email: Switch delivery to Daily Digest | Switch format =
to Traditional=20
Visit Your Group | Yahoo! Groups Terms of Use | Unsubscribe=20
Recent Activity
* =A014
New Members
* =A01
New FilesVisit Your Group=20
Yahoo! Finance
It's Now Personal
Guides, news,
advice & more.
New web site?
Drive traffic now.
Get your business
on Yahoo! search.
All-Bran
10 Day Challenge
Join the club and
feel the benefits.
.=20
=20
=20=20=20=20=20=20

[Non-text portions of this message have been removed]
------------------------------------



(You need to be a member of msp430 -- send a blank email to msp430-subscribe@yahoogroups.com )

Hello,

yesterday i unpacked a F5438 USB FET that i arrived some days ago from
digikey. There was a sheet of paper telling me the kit should include
a CDRom and two MSP430F5438 parts. None of those, instead one piece
labeled XM430F5438, which may be an engineering sample or so. The part
fits into the TQ100 socket of the FET.
Then i downloaded the current KickStart, about 50 MBytes. There was
some problem with the myTI login. I had to try on several computers
and browsers until the download finally started. After connecting and
installing everything on a XP machine (USB drivers from IAR
subdirectory), i started the IDE, opened the "FLashing the LED"
workspace and activated the "MSP430x5xx (C) - Debug" project. In the
project options i had to change the processor from F5419 to
XMS430F5438. Then it started debugging and blinking the LED without
any messages or problems. The FET jumpers were default and set for the
classic JTAG like you are trying to use.
Right now i connected everything again using one of the old Olimex LPT
JTAGs we have, and after selecting the parallel port in the project
options it worked immediately and blinked the LED.

Regards,
Dieter=20

--- In m...@yahoogroups.com, mm bb wrote:
>
> Hello, I m trying to program this micro XMS430F5438, using a
parallel jtag interface and IAR V4.11B/W32 (4.11.2.9), but I get an
error as the chip is not connected. From the micro side I only have
the VCC, gnd and the pins for the Jtag, (TDO,TDI,TMS,TCK, TEST)=C2 the
reset is pulled up
>=20
> From the jtag side I have one home made circuit=C2 copied from TI.
Where could be the problem?.Have I missed something important?=20
> Thanks for your help.
>=20
>=20
> Yahoo! Cocina
> Recetas pr=C3=A1cticas y comida saludable
> http://ar.mujer.yahoo.com/cocina/
>=20
> [Non-text portions of this message have been removed]
>

------------------------------------



(You need to be a member of msp430 -- send a blank email to msp430-subscribe@yahoogroups.com )

The XM part is the prototype silicon part. This has a number of published
errata and a couple of things that are missing, most notably from my point
of view there is no calibration data in the on chip flash. The transfer
function of the on chip temperature sensor has not been published so when I
use my F149 code I get a temperature of 9 deg C in the office.

Ian

2008/9/19 dietert1

> Hello,
>
> yesterday i unpacked a F5438 USB FET that i arrived some days ago from
> digikey. There was a sheet of paper telling me the kit should include
> a CDRom and two MSP430F5438 parts. None of those, instead one piece
> labeled XM430F5438, which may be an engineering sample or so. The part
> fits into the TQ100 socket of the FET.
> Then i downloaded the current KickStart, about 50 MBytes. There was
> some problem with the myTI login. I had to try on several computers
> and browsers until the download finally started. After connecting and
> installing everything on a XP machine (USB drivers from IAR
> subdirectory), i started the IDE, opened the "FLashing the LED"
> workspace and activated the "MSP430x5xx (C) - Debug" project. In the
> project options i had to change the processor from F5419 to
> XMS430F5438. Then it started debugging and blinking the LED without
> any messages or problems. The FET jumpers were default and set for the
> classic JTAG like you are trying to use.
> Right now i connected everything again using one of the old Olimex LPT
> JTAGs we have, and after selecting the parallel port in the project
> options it worked immediately and blinked the LED.
>
> Regards,
> Dieter
>
> --- In m...@yahoogroups.com, mm bb wrote:
> >
> > Hello, I m trying to program this micro XMS430F5438, using a
> parallel jtag interface and IAR V4.11B/W32 (4.11.2.9), but I get an
> error as the chip is not connected. From the micro side I only have
> the VCC, gnd and the pins for the Jtag, (TDO,TDI,TMS,TCK, TEST)=C2 the
> reset is pulled up
> >
> > From the jtag side I have one home made circuit=C2 copied from TI.
> Where could be the problem?.Have I missed something important?
> > Thanks for your help.
> >
> >
> > Yahoo! Cocina
> > Recetas pr=C3=A1cticas y comida saludable
> > http://ar.mujer.yahoo.com/cocina/
> >
> > [Non-text portions of this message have been removed]
> > ------------------------------------



(You need to be a member of msp430 -- send a blank email to msp430-subscribe@yahoogroups.com )

That's amazing, an air conditioner, implemented in software, on a chip=20
that draws just a few micro-amps. We can all relax, the environment is=20
saved!! yeah, Go Ti :@}

Al

Ian Okey wrote:

>The XM part is the prototype silicon part. This has a number of published
>errata and a couple of things that are missing, most notably from my point
>of view there is no calibration data in the on chip flash. The transfer
>function of the on chip temperature sensor has not been published so when =
I
>use my F149 code I get a temperature of 9 deg C in the office.
>
>Ian
>
>2008/9/19 dietert1 =20=20
>
>>Hello,
>>
>>yesterday i unpacked a F5438 USB FET that i arrived some days ago from
>>digikey. There was a sheet of paper telling me the kit should include
>>a CDRom and two MSP430F5438 parts. None of those, instead one piece
>>labeled XM430F5438, which may be an engineering sample or so. The part
>>fits into the TQ100 socket of the FET.
>>Then i downloaded the current KickStart, about 50 MBytes. There was
>>some problem with the myTI login. I had to try on several computers
>>and browsers until the download finally started. After connecting and
>>installing everything on a XP machine (USB drivers from IAR
>>subdirectory), i started the IDE, opened the "FLashing the LED"
>>workspace and activated the "MSP430x5xx (C) - Debug" project. In the
>>project options i had to change the processor from F5419 to
>>XMS430F5438. Then it started debugging and blinking the LED without
>>any messages or problems. The FET jumpers were default and set for the
>>classic JTAG like you are trying to use.
>>Right now i connected everything again using one of the old Olimex LPT
>>JTAGs we have, and after selecting the parallel port in the project
>>options it worked immediately and blinked the LED.
>>
>>Regards,
>>Dieter
>>
>>--- In m...@yahoogroups.com, mm bb wrote:
>>=20=20=20=20
>>
>>>Hello, I m trying to program this micro XMS430F5438, using a
>>>=20=20=20=20=20=20
>>>
>>parallel jtag interface and IAR V4.11B/W32 (4.11.2.9), but I get an
>>error as the chip is not connected. From the micro side I only have
>>the VCC, gnd and the pins for the Jtag, (TDO,TDI,TMS,TCK, TEST)=C2 the
>>reset is pulled up
>>=20=20=20=20
>>
>>>From the jtag side I have one home made circuit=C2 copied from TI.
>>>=20=20=20=20=20=20
>>>
>>Where could be the problem?.Have I missed something important?
>>=20=20=20=20
>>
>>>Thanks for your help.
>>>
>>>
>>> Yahoo! Cocina
>>>Recetas pr=C3=A1cticas y comida saludable
>>>http://ar.mujer.yahoo.com/cocina/
>>>
>>>[Non-text portions of this message have been removed]
>>>
>>>=20=20=20=20=20=20
>>>------------------------------------



(You need to be a member of msp430 -- send a blank email to msp430-subscribe@yahoogroups.com )

:-D

2008/9/19 Onestone

> That's amazing, an air conditioner, implemented in software, on a chip
> that draws just a few micro-amps. We can all relax, the environment is
> saved!! yeah, Go Ti :@}
>
> Al
>
> Ian Okey wrote:
>
> >The XM part is the prototype silicon part. This has a number of publish=
ed
> >errata and a couple of things that are missing, most notably from my poi=
nt
> >of view there is no calibration data in the on chip flash. The transfer
> >function of the on chip temperature sensor has not been published so whe=
n
> I
> >use my F149 code I get a temperature of 9 deg C in the office.
> >
> >Ian
> >
> >2008/9/19 dietert1
> >
> >
> >
> >>Hello,
> >>
> >>yesterday i unpacked a F5438 USB FET that i arrived some days ago from
> >>digikey. There was a sheet of paper telling me the kit should include
> >>a CDRom and two MSP430F5438 parts. None of those, instead one piece
> >>labeled XM430F5438, which may be an engineering sample or so. The part
> >>fits into the TQ100 socket of the FET.
> >>Then i downloaded the current KickStart, about 50 MBytes. There was
> >>some problem with the myTI login. I had to try on several computers
> >>and browsers until the download finally started. After connecting and
> >>installing everything on a XP machine (USB drivers from IAR
> >>subdirectory), i started the IDE, opened the "FLashing the LED"
> >>workspace and activated the "MSP430x5xx (C) - Debug" project. In the
> >>project options i had to change the processor from F5419 to
> >>XMS430F5438. Then it started debugging and blinking the LED without
> >>any messages or problems. The FET jumpers were default and set for the
> >>classic JTAG like you are trying to use.
> >>Right now i connected everything again using one of the old Olimex LPT
> >>JTAGs we have, and after selecting the parallel port in the project
> >>options it worked immediately and blinked the LED.
> >>
> >>Regards,
> >>Dieter
> >>
> >>--- In m...@yahoogroups.com, mm bb wrote:
> >>
> >>
> >>>Hello, I m trying to program this micro XMS430F5438, using a
> >>>
> >>>
> >>parallel jtag interface and IAR V4.11B/W32 (4.11.2.9), but I get an
> >>error as the chip is not connected. From the micro side I only have
> >>the VCC, gnd and the pins for the Jtag, (TDO,TDI,TMS,TCK, TEST)=C2 the
> >>reset is pulled up
> >>
> >>
> >>>From the jtag side I have one home made circuit=C2 copied from TI.
> >>>
> >>>
> >>Where could be the problem?.Have I missed something important?
> >>
> >>
> >>>Thanks for your help.
> >>>
> >>>
> >>> Yahoo! Cocina
> >>>Recetas pr=C3=A1cticas y comida saludable
> >>>http://ar.mujer.yahoo.com/cocina/
> >>>
> >>>[Non-text portions of this message have been removed]
> >>>
> >>>
> >>>
> >>
> >>------------------------------------
> >>
> >>
> >>
> >>



(You need to be a member of msp430 -- send a blank email to msp430-subscribe@yahoogroups.com )

In the last hour or so TI have published an updated datasheet for the 5438
chip. This includes the temperature sensor characteristic. A little
bedtime reading now being printed.

Ian

2008/9/19 Ian Okey

> The XM part is the prototype silicon part. This has a number of publishe=
d
> errata and a couple of things that are missing, most notably from my poin=
t
> of view there is no calibration data in the on chip flash. The transfer
> function of the on chip temperature sensor has not been published so when=
I
> use my F149 code I get a temperature of 9 deg C in the office.
>
> Ian
>
> 2008/9/19 dietert1 Hello,
>>
>> yesterday i unpacked a F5438 USB FET that i arrived some days ago from
>> digikey. There was a sheet of paper telling me the kit should include
>> a CDRom and two MSP430F5438 parts. None of those, instead one piece
>> labeled XM430F5438, which may be an engineering sample or so. The part
>> fits into the TQ100 socket of the FET.
>> Then i downloaded the current KickStart, about 50 MBytes. There was
>> some problem with the myTI login. I had to try on several computers
>> and browsers until the download finally started. After connecting and
>> installing everything on a XP machine (USB drivers from IAR
>> subdirectory), i started the IDE, opened the "FLashing the LED"
>> workspace and activated the "MSP430x5xx (C) - Debug" project. In the
>> project options i had to change the processor from F5419 to
>> XMS430F5438. Then it started debugging and blinking the LED without
>> any messages or problems. The FET jumpers were default and set for the
>> classic JTAG like you are trying to use.
>> Right now i connected everything again using one of the old Olimex LPT
>> JTAGs we have, and after selecting the parallel port in the project
>> options it worked immediately and blinked the LED.
>>
>> Regards,
>> Dieter
>>
>> --- In m...@yahoogroups.com, mm bb wrote:
>> >
>> > Hello, I m trying to program this micro XMS430F5438, using a
>> parallel jtag interface and IAR V4.11B/W32 (4.11.2.9), but I get an
>> error as the chip is not connected. From the micro side I only have
>> the VCC, gnd and the pins for the Jtag, (TDO,TDI,TMS,TCK, TEST)=C2 the
>> reset is pulled up
>> >
>> > From the jtag side I have one home made circuit=C2 copied from TI.
>> Where could be the problem?.Have I missed something important?
>> > Thanks for your help.
>> >
>> >
>> > Yahoo! Cocina
>> > Recetas pr=C3=A1cticas y comida saludable
>> > http://ar.mujer.yahoo.com/cocina/
>> >
>> > [Non-text portions of this message have been removed]
>> >
>>
>> ------------------------------------



(You need to be a member of msp430 -- send a blank email to msp430-subscribe@yahoogroups.com )