Sign in
Search AT91SAM
Subscribe to AT91SAM
Ads
Discussion Groups
See Also
Discussion Groups | AT91SAM ARM | RE: AT91SAM9263-EK will not power-up
For users of the Atmel AT91SAM7 and AT91SAM9 ARM CPU chips. Atmel has taken a new direction by combining on chip flash and ram with the ARM CPU on a single die. This provides low cost devices for small systems using the ARM CPU. This group is to exchange information to help users get started and learn how to use the devices.
RE: AT91SAM9263-EK will not power-up - "Chen, Weiguo (GE, Research)" - Nov 18 21:58:49 2009
Hi Andrew,
Try changing the J2 setting, "Force Power On".
Looks like your power circuit was not started.
Good luck
Weiguo
________________________________
From: A...@yahoogroups.com [mailto:A...@yahoogroups.com] On Behalf
Of brimer.andrew
Sent: Thursday, November 19, 2009 5:28 AM
To: A...@yahoogroups.com
Subject: [AT91SAM] AT91SAM9263-EK will not power-up
I got the AT91SAM9263-EK in this morning and have not worked with Atmel
before. I verified the jumper settings as per the welcome.html from the
Atmel CD and they all were as described. I plugged in the power and the
power LED did not activate, the EK is as if there is no power.
The power supply sent from Atmel is +12V out and I checked with a Fluke
116 multimeter: it is outputting 12.1V
I connected the power to the EK and the female on the board is showing
12.1V as well. This has to be a jumper setting issue (I hope) and not
that I have to return the EK to Atmel for another.
Can someone please help me? I want to get into working with the new
development environment and can do nothing.
Regards,
Andrew
(You need to be a member of AT91SAM -- send a blank email to AT91SAM-subscribe@yahoogroups.com )
Re: AT91SAM9263-EK will not power-up - Andrew Brimer - Nov 19 8:22:41 2009
Thank you so very much Weiguo,
I now have the board up and running. I had concerns regarding a forced power on and needed to hear from someone more experienced than I. Can I now open J2, or can it remain closed? Thank you again for the help, now I can get started on getting the operating system tuned.
Regards,
Andrew
________________________________
From: "Chen, Weiguo (GE, Research)"
To: A...@yahoogroups.com
Sent: Wed, November 18, 2009 9:15:53 PM
Subject: RE: [AT91SAM] AT91SAM9263-EK will not power-up
Hi Andrew,
Try changing the J2 setting, "Force Power On".
Looks like your power circuit was not started.
Good luck
Weiguo
________________________________
From: AT91SAM@yahoogroups .com [mailto:AT91SAM@ yahoogroups. com] On Behalf Of brimer.andrew
Sent: Thursday, November 19, 2009 5:28 AM
To: AT91SAM@yahoogroups .com
Subject: [AT91SAM] AT91SAM9263- EK will not power-up
I got the AT91SAM9263- EK in this morning and have not worked with Atmel before. I verified the jumper settings as per the welcome.html from the Atmel CD and they all were as described.. I plugged in the power and the power LED did not activate, the EK is as if there is no power.
The power supply sent from Atmel is +12V out and I checked with a Fluke 116 multimeter: it is outputting 12.1V
I connected the power to the EK and the female on the board is showing 12.1V as well. This has to be a jumper setting issue (I hope) and not that I have to return the EK to Atmel for another.
Can someone please help me? I want to get into working with the new development environment and can do nothing.
Regards,
Andrew
(You need to be a member of AT91SAM -- send a blank email to AT91SAM-subscribe@yahoogroups.com )
I now have the board up and running. I had concerns regarding a forced power on and needed to hear from someone more experienced than I. Can I now open J2, or can it remain closed? Thank you again for the help, now I can get started on getting the operating system tuned.
Regards,
Andrew
________________________________
From: "Chen, Weiguo (GE, Research)"
To: A...@yahoogroups.com
Sent: Wed, November 18, 2009 9:15:53 PM
Subject: RE: [AT91SAM] AT91SAM9263-EK will not power-up
Hi Andrew,
Try changing the J2 setting, "Force Power On".
Looks like your power circuit was not started.
Good luck
Weiguo
________________________________
From: AT91SAM@yahoogroups .com [mailto:AT91SAM@ yahoogroups. com] On Behalf Of brimer.andrew
Sent: Thursday, November 19, 2009 5:28 AM
To: AT91SAM@yahoogroups .com
Subject: [AT91SAM] AT91SAM9263- EK will not power-up
I got the AT91SAM9263- EK in this morning and have not worked with Atmel before. I verified the jumper settings as per the welcome.html from the Atmel CD and they all were as described.. I plugged in the power and the power LED did not activate, the EK is as if there is no power.
The power supply sent from Atmel is +12V out and I checked with a Fluke 116 multimeter: it is outputting 12.1V
I connected the power to the EK and the female on the board is showing 12.1V as well. This has to be a jumper setting issue (I hope) and not that I have to return the EK to Atmel for another.
Can someone please help me? I want to get into working with the new development environment and can do nothing.
Regards,
Andrew
(You need to be a member of AT91SAM -- send a blank email to AT91SAM-subscribe@yahoogroups.com )