Sign in

username:

password:



Not a member?

Search AT91SAM



Search tips

Subscribe to AT91SAM



Ads

Discussion Groups

AT91SAM ARM

For users of the Atmel AT91SAM7 and AT91SAM9 ARM CPU chips. Atmel has taken a new direction by combining on chip flash and ram with the ARM CPU on a single die. This provides low cost devices for small systems using the ARM CPU. This group is to exchange information to help users get started and learn how to use the devices.

  

Post a new Thread

Re: Trouble in SAM-BA programming   [2 Articles]

vinaydand - Aug 19 2008
Hello, 1) Try with 40 Sec. instead of 10 sec - to allow more time for SAM- BA bootloader to be transfered to RAM Regards Vinay --- In A...@yahoogroups.com, "s_samiee_s" ... Re: Trouble in SAM-BA programming

[at91sam7x256] Problem with connecting serial FLASH using SPI   [3 Articles]

dawido85 - Aug 19 2008
Hi, I'm trying to read JEDEC from my serial FLASH, but I keep getting wrong id. I tested LLB and MISO/MOSI hard loop, both get me proper data. Can somebody enlight me where I'm... [at91sam7x256] Problem with connecting serial FLASH using SPI

Global Variable   [2 Articles]

bhav...@yahoo.com - Aug 17 2008
I m using SAM-BA 2.6 to program AT91SAM7x512. Previously there was _stack_end = 0x20FFFC which i have modified to _stack_end = 0x21FFF8 for 128KBytes of RAM. I have got solution by... Global Variable

Global Variable   [2 Articles]

bhav...@yahoo.com - Aug 17 2008
Thanks for suggestions...... But What exactly my problem is that as i add global variables in my project,my code stop working. I m using YAGARTO tool. Which compile my code based o... Global Variable

data bus problem   [3 Articles]

Bernd - Aug 13 2008
Hi, I`m working with the AT91SAM9260 and the AT49BV160D nor flash memory. I`m able to read out the flash manufactor code - therefore I have to write 0x98 at any adress wi... data bus problem

AT91SAM7x512   [6 Articles]

bhav...@yahoo.com - Aug 13 2008
I m using AT91SAM7x512. I m using YAGARTO tool to compile my code. My code is working ok. But, I have one problem is that As I add more variables than my code is not working. I hav... AT91SAM7x512

SPI1 Loop Back on AT91SAM7X-EK   [2 Articles]

hudson_low - Aug 12 2008
Hi, Any one have Problem with SPI1? I am using my SAM7-EK to test the SPI code. I started to test the spi code with internal loop back. SPI_MR =(AT91C_SPI_MSTR | AT91C_SP... SPI1 Loop Back on AT91SAM7X-EK

new bee for at91sam   [4 Articles]

manhar_varu - Aug 10 2008
hi, please let me know that for programming this cheap, i need only jtag ? can we program the this chip directly via parallel port? if yes then please send me software links.... new bee for at91sam

[ann] eLua 0.3 released

Bogdan Marinescu - Aug 9 2008
Hi, eLua is an effort to bring the Lua programming language in the embedded world (MCUs). It is meant to be a complete MCU development environment. It currently runs on a numb... [ann] eLua 0.3 released

timing calculation   [3 Articles]

Bernd - Aug 6 2008
Hi, I`ve a question about timing. The trace difference is 40mm, the frequency is 96MHz and the FR4-material-speed is approximately 0.16 m/ns. How do I`ve to calculate th... timing calculation
previous | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | 10 | 11 | 12 | 13 | 14 | 15 | 16 | 17 | 18 | 19 | 20 | next